Supported Inputs

Built-In Inputs (System)~

AoT: AoT Version~

Manufacturer: AoT
Measurements: Version as Major.Minor.Revision

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions

AoT: CPU Load~

Manufacturer: AoT
Measurements: CPULoad
Libraries: os.getloadavg()

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions

AoT: Free Space~

Manufacturer: AoT
Measurements: Unallocated Disk Space
Libraries: os.statvfs()

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions

AoT: GL: Aerial Photo Overlay~

Manufacturer: AoT
Measurements: Status
Libraries: gis_image_overlay

Overlay a user-uploaded aerial or drone photo on the map. On upload, GPS and camera pose embedded in the photo (EXIF/XMP) are used to place it automatically; the four corners can then be dragged to fine-tune the fit against map features.

Option	Type	Description
Image URL
Corner coordinates (JSON)
Opacity
Extracted metadata (JSON)

AoT: Output State (On/Off)~

Manufacturer: AoT
Measurements: Boolean

This Input stores a 0 (off) or 1 (on) for the selected On/Off Output.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
On/Off Output Channel	Select Channel (Output_Channels)	Select an output to measure

AoT: Remote AoT: Measurements~

Manufacturer: AoT
Measurements: Variable measurements
Libraries: requests
Dependencies: requests

Collect measurements from another AoT server over the network using its API. Enter the host and API key, set the number of measurements, and save — the Remote Measurement dropdown is then filled with the channels available on that server. Pick one per channel and set its Measurement Unit to match the unit shown in the dropdown. Values arrive with the remote timestamp, and any conversion configured on the remote channel is already applied.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Start Offset (Seconds)	Integer	The duration to wait before the first operation
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Remote AoT Host	Text	The host or IP address of the remote AoT (a port may be included, e.g. 192.168.0.9:8084)
Remote AoT API Key	Text	The API key of the remote AoT, exactly as shown on that server
Protocol	Select(Options: [HTTPS \| HTTP] (Default in bold)	Use HTTPS unless the remote AoT is only reachable over plain HTTP on a trusted network
Verify TLS Certificate	Boolean - Default Value: True	Verify the remote server certificate. Turn this off only for a self-signed certificate on a trusted network — while off, the API key can be read by a man in the middle
Request Timeout (Seconds)	Integer - Default Value: 30	HTTP read timeout. Raise it if the remote server is slow to answer a large batch
Initial Backfill (Hours)	Integer - Default Value: 24	How far back to collect on the first run. Later runs only fetch what has arrived since the last collection
Channel Options
Name	Text	A name to distinguish this from others
Remote Measurement	The measurement on the remote AoT to collect into this channel

AoT: Server Ping~

Manufacturer: AoT
Measurements: Boolean
Libraries: ping

This Input executes the bash command "ping -c [times] -w [deadline] [host]" to determine if the host can be pinged.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AoT: Server Port Open~

Manufacturer: AoT
Measurements: Boolean
Libraries: nc

This Input executes the bash command "nc -zv [host] [port]" to determine if the host at a particular port is accessible.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AoT: Spacer~

Manufacturer: AoT

A spacer to organize Inputs.

Option	Type	Description
Color	Text - Default Value: #000000	The color of the name text

AoT: System and AoT RAM~

Manufacturer: AoT
Measurements: RAM Allocation
Libraries: psutil, resource.getrusage()
Dependencies: psutil

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
AoT Frontend RAM Endpoint	Text - Default Value: https://127.0.0.1/ram	The endpoint to get AoT frontend ram usage

AoT: Test Input: Save your own measurement value~

Manufacturer: AoT
Measurements: Variable measurements

This is a simple test Input that allows you to save any value as a measurement, that will be stored in the measurement database. It can be useful for testing other parts of AoT, such as PIDs, Bang-Bang, and Conditional Functions, since you can be completely in control of what values the input provides to the Functions. Note 1: Select and save the Name and Measurement Unit for each channel. Once the unit has been saved, you can convert to other units in the Convert Measurement section. Note 2: Activate the Input before storing measurements.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Channel Options
Name	Text	A name to distinguish this from others
Commands
Enter the Value you want to store as a measurement, then press Store Measurement.
Channel	Integer	This is the channel to save the measurement value to
Value	Decimal - Default Value: 10.0	This is the measurement value to save for this Input
Store Measurement	Button

AoT: Uptime~

Manufacturer: AoT
Measurements: Seconds Since System Startup

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions

Linux: Bash Command~

Manufacturer: Linux
Measurements: Return Value
Interfaces: AoT

This Input will execute a command in the shell and store the output as a float value. Perform any unit conversions within your script or command. A measurement/unit is required to be selected.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Command Timeout	Integer - Default Value: 60	How long to wait for the command to finish before killing the process.
User	Text - Default Value: aot	The user to execute the command
Current Working Directory	Text - Default Value: /home/pi	The current working directory of the shell environment.

Linux: Python 3 Code (v1.0)~

Manufacturer: Linux
Measurements: Store Value(s)
Interfaces: AoT
Dependencies: pylint

All channels require a Measurement Unit to be selected and saved in order to store values to the database. Your code is executed from the same Python virtual environment that AoT runs from. Therefore, you must install Python libraries to this environment if you want them to be available to your code. This virtualenv is located at /opt/AoT/env and if you wanted to install a library, for example "my_library" using pip, you would execute "sudo /opt/AoT/env/bin/pip install my_library".

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Analyze Python Code with Pylint	Boolean - Default Value: True	Analyze your Python code with pylint when saving

Linux: Python 3 Code (v2.0)~

Manufacturer: Linux
Measurements: Store Value(s)
Interfaces: AoT
Dependencies: pylint

This is an alternate Python 3 Code Input that uses a different method for storing values to the database. This was created because the Python 3 Code v1.0 Input does not allow the use of Input Actions. This method does allow the use of Input Actions. (11/21/2023 Update: The Python 3 Code (v1.0) Input now allows the execution of Actions). All channels require a Measurement Unit to be selected and saved in order to store values to the database. Your code is executed from the same Python virtual environment that AoT runs from. Therefore, you must install Python libraries to this environment if you want them to be available to your code. This virtualenv is located at /opt/AoT/env and if you wanted to install a library, for example "my_library" using pip, you would execute "sudo /opt/AoT/env/bin/pip install my_library".

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Python 3 Code	The code to execute. Must return a value.
Analyze Python Code with Pylint	Boolean - Default Value: True	Analyze your Python code with pylint when saving

Raspberry Pi: CPU/GPU Temperature~

Manufacturer: Raspberry Pi
Measurements: Temperature
Interfaces: RPi

The internal CPU and GPU temperature of the Raspberry Pi.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Path for CPU Temperature	Text - Default Value: /sys/class/thermal/thermal_zone0/temp	Reads the CPU temperature from this file
Path to vcgencmd	Text - Default Value: /usr/bin/vcgencmd	Reads the GPU from vcgencmd

Raspberry Pi: Edge Detection~

Manufacturer: Raspberry Pi
Measurements: Rising/Falling Edge
Interfaces: GPIO
Libraries: RPi.GPIO
Dependencies: RPi.GPIO

Option	Type	Description
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Pin Mode	Select(Options: [Floating \| Pull Down \| Pull Up] (Default in bold)	Enables or disables the pull-up or pull-down resistor

Raspberry Pi: GPIO State~

Manufacturer: Raspberry Pi
Measurements: GPIO State
Interfaces: GPIO
Libraries: RPi.GPIO
Dependencies: RPi.GPIO

Measures the state of a GPIO pin, returning either 0 (low) or 1 (high).

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Pin Mode	Select(Options: [Floating \| Pull Down \| Pull Up] (Default in bold)	Enables or disables the pull-up or pull-down resistor

Raspberry Pi: Signal (PWM)~

Manufacturer: Raspberry Pi
Measurements: Frequency/Pulse Width/Duty Cycle
Interfaces: GPIO
Libraries: pigpio
Dependencies: pigpio, pigpio

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Raspberry Pi: Signal (Revolutions) (pigpio method #1)~

Manufacturer: Raspberry Pi
Measurements: RPM
Interfaces: GPIO
Libraries: pigpio
Dependencies: pigpio, pigpio

This calculates RPM from pulses on a pin using pigpio, but has been found to be less accurate than the method #2 module. This is typically used to measure the speed of a fan from a tachometer pin, however this can be used to measure any 3.3-volt pulses from a wire. Use a resistor to pull the measurement pin to 3.3 volts, set pigpio to the lowest latency (1 ms) on the Configure -> Raspberry Pi page. Note 1: Not setting pigpio to the lowest latency will hinder accuracy. Note 2: accuracy decreases as RPM increases.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Raspberry Pi: Signal (Revolutions) (pigpio method #2)~

Manufacturer: Raspberry Pi
Measurements: RPM
Interfaces: GPIO
Libraries: pigpio
Dependencies: pigpio, pigpio

This is an alternate method to calculate RPM from pulses on a pin using pigpio, and has been found to be more accurate than the method #1 module. This is typically used to measure the speed of a fan from a tachometer pin, however this can be used to measure any 3.3-volt pulses from a wire. Use a resistor to pull the measurement pin to 3.3 volts, set pigpio to the lowest latency (1 ms) on the Configure -> Raspberry Pi page. Note 1: Not setting pigpio to the lowest latency will hinder accuracy. Note 2: accuracy decreases as RPM increases.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Pin: GPIO (BCM)	Integer	The pin to measure pulses from
Sample Time (Seconds)	Decimal - Default Value: 5.0	The duration of time to sample
Pulses Per Rev	Decimal - Default Value: 15.8	The number of pulses per revolution to calculate revolutions per minute (RPM)

Built-In Inputs (Devices)~

AMS: AS7262~

Manufacturer: AMS
Measurements: Light at 450, 500, 550, 570, 600, 650 nm
Interfaces: I²C
Libraries: as7262
Dependencies: as7262
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Gain	Select(Options: [1x \| 3.7x \| 16x \| 64x] (Default in bold)	Set the sensor gain
Illumination LED Current	Select(Options: [12.5 mA \| 25 mA \| 50 mA \| 100 mA] (Default in bold)	Set the illumination LED current (milliamps)
Illumination LED Mode	Select(Options: [On \| Off] (Default in bold)	Turn the illumination LED on or off during a measurement
Indicator LED Current	Select(Options: [1 mA \| 2 mA \| 4 mA \| 8 mA] (Default in bold)	Set the indicator LED current (milliamps)
Indicator LED Mode	Select(Options: [On \| Off] (Default in bold)	Turn the indicator LED on or off during a measurement
Integration Time	Decimal - Default Value: 15.0	The integration time (0 - ~91 ms)

AMS: CCS811 (with Temperature)~

Manufacturer: AMS
Measurements: CO2/VOC/Temperature
Interfaces: I²C
Libraries: Adafruit_CCS811
Dependencies: Adafruit_CCS811, Adafruit-GPIO
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AMS: CCS811 (without Temperature)~

Manufacturer: AMS
Measurements: CO2/VOC
Interfaces: I²C
Libraries: Adafruit_CircuitPython_CCS811
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-ccs811
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link
Additional URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AMS: TSL2561~

Manufacturer: AMS
Measurements: Light
Interfaces: I²C
Libraries: tsl2561
Dependencies: Adafruit-GPIO, Adafruit-PureIO, tsl2561
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AMS: TSL2591~

Manufacturer: AMS
Measurements: Light
Interfaces: I²C
Libraries: maxlklaxl/python-tsl2591
Dependencies: tsl2591
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AOSONG: AM2315/AM2320~

Manufacturer: AOSONG
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: quick2wire-api
Dependencies: quick2wire-api
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AOSONG: AM2315C~

Manufacturer: AOSONG
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: quick2wire-api
Dependencies: quick2wire-api
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AOSONG: DHT11~

Manufacturer: AOSONG
Measurements: Humidity/Temperature
Interfaces: GPIO
Libraries: pigpio
Dependencies: pigpio, pigpio
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AOSONG: DHT20~

Manufacturer: AOSONG
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: smbus2
Dependencies: smbus2
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2, Link 3

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

AOSONG: DHT22~

Manufacturer: AOSONG
Measurements: Humidity/Temperature
Interfaces: GPIO
Libraries: pigpio
Dependencies: pigpio, pigpio
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

ASAIR: AHTx0~

Manufacturer: ASAIR
Measurements: Temperature/Humidity
Interfaces: I²C
Libraries: Adafruit_CircuitPython_AHTx0
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-ahtx0
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Adafruit: I2C Capacitive Moisture Sensor~

Manufacturer: Adafruit
Measurements: Moisture/Temperature
Interfaces: I²C
Libraries: adafruit_seesaw
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-seesaw
Manufacturer URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Analog Devices: ADT7410~

Manufacturer: Analog Devices
Measurements: Temperature
Interfaces: I²C
Libraries: Adafruit_CircuitPython_ADT7410
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-adt7410
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Analog Devices: ADXL34x (343, 344, 345, 346)~

Manufacturer: Analog Devices
Measurements: Acceleration
Interfaces: I²C
Libraries: Adafruit_CircuitPython_ADXL34x
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-adxl34x
Datasheet URLs: Link 1, Link 2, Link 3, Link 4
Product URLs: Link 1, Link 2, Link 3, Link 4

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Range	Select(Options: [±2 g (±19.6 m/s/s) \| ±4 g (±39.2 m/s/s) \| ±8 g (±78.4 m/s/s) \| ±16 g (±156.9 m/s/s)] (Default in bold)	Set the measurement range

AnyLeaf: AnyLeaf EC~

Manufacturer: AnyLeaf
Measurements: Electrical Conductivity
Interfaces: UART
Libraries: anyleaf
Dependencies: libjpeg-dev, zlib1g-dev, Pillow, scipy>=1.7.0, pyusb, Adafruit-extended-bus, anyleaf
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Conductivity Constant	Decimal - Default Value: 1.0	Conductivity constant K

AnyLeaf: AnyLeaf ORP~

Manufacturer: AnyLeaf
Measurements: Oxidation Reduction Potential
Interfaces: I²C
Libraries: anyleaf
Dependencies: libjpeg-dev, zlib1g-dev, Pillow, scipy>=1.7.0, pyusb, Adafruit-extended-bus, anyleaf
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Calibrate: Voltage (Internal)	Decimal - Default Value: 0.4	Calibration data: internal voltage
Calibrate: ORP (Internal)	Decimal - Default Value: 400.0	Calibration data: internal ORP
Commands
Calibrate: Buffer ORP (mV)	Decimal - Default Value: 400.0	This is the nominal ORP of the calibration buffer in mV, usually labelled on the bottle.
Calibrate	Button
Clear Calibration Slots	Button

AnyLeaf: AnyLeaf pH~

Manufacturer: AnyLeaf
Measurements: Ion concentration
Interfaces: I²C
Libraries: anyleaf
Dependencies: libjpeg-dev, zlib1g-dev, Pillow, scipy>=1.7.0, pyusb, Adafruit-extended-bus, anyleaf
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Temperature Compensation: Measurement	Select Measurement (Input, Function)	Select a measurement for temperature compensation
Temperature Compensation: Max Age (Seconds)	Integer - Default Value: 120	The maximum age of the measurement to use
Cal data: V1 (internal)	Decimal	Calibration data: Voltage
Cal data: pH1 (internal)	Decimal - Default Value: 7.0	Calibration data: pH
Cal data: T1 (internal)	Decimal - Default Value: 23.0	Calibration data: Temperature
Cal data: V2 (internal)	Decimal - Default Value: 0.17	Calibration data: Voltage
Cal data: pH2 (internal)	Decimal - Default Value: 4.0	Calibration data: pH
Cal data: T2 (internal)	Decimal - Default Value: 23.0	Calibration data: Temperature
Cal data: V3 (internal)	Decimal	Calibration data: Voltage
Cal data: pH3 (internal)	Decimal	Calibration data: pH
Cal data: T3 (internal)	Decimal	Calibration data: Temperature
Commands
Calibration buffer pH	Decimal - Default Value: 7.0	This is the nominal pH of the calibration buffer, usually labelled on the bottle.
Calibrate, slot 1	Button
Calibrate, slot 2	Button
Calibrate, slot 3	Button
Clear Calibration Slots	Button

Atlas Scientific: Atlas CO2 (Carbon Dioxide Gas)~

Manufacturer: Atlas Scientific
Measurements: CO2
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Commands
A one- or two-point calibration can be performed. After exposing the probe to a concentration of CO2 between 3,000 and 5,000 ppmv until readings stabilize, press Calibrate (High). You can place the probe in a 0 CO2 environment until readings stabilize, then press Calibrate (Zero). You can also clear the currently-saved calibration by pressing Clear Calibration, returning to the factory-set calibration. Status messages will be sent to the Daemon Log, accessible from Config -> AoT Logs -> Daemon Log.
High Point CO2	Integer - Default Value: 3000	The high CO2 calibration point (3000 - 5000 ppmv)
Calibrate (High)	Button
Calibrate (Zero)	Button
Clear Calibration	Button
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x69	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas Color~

Manufacturer: Atlas Scientific
Measurements: RGB, CIE, LUX, Proximity
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
LED Only For Measure	Boolean - Default Value: True	Turn the LED on only during the measurement
LED Percentage	Integer - Default Value: 30	What percentage of power to supply to the LEDs during measurement
Gamma Correction	Decimal - Default Value: 1.0	Gamma correction between 0.01 and 4.99 (default is 1.0)
Commands
The EZO-RGB color sensor is designed to be calibrated to a white object at the maximum brightness the object will be viewed under. In order to get the best results, Atlas Scientific strongly recommends that the sensor is mounted into a fixed location. Holding the sensor in your hand during calibration will decrease performance. 1. Embed the EZO-RGB color sensor into its intended use location. 2. Set LED brightness to the desired level. 3. Place a white object in front of the target object and press the Calibration button. 4. A single color reading will be taken and the device will be fully calibrated.
Calibrate	Button
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x70	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas DO~

Manufacturer: Atlas Scientific
Measurements: Dissolved Oxygen
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Compensation: Measurement	Select Measurement (Input, Function)	Select a measurement for temperature compensation
Temperature Compensation: Max Age (Seconds)	Integer - Default Value: 120	The maximum age of the measurement to use
Commands
A one- or two-point calibration can be performed. After exposing the probe to air for 30 seconds until readings stabilize, press Calibrate (Air). If you require accuracy below 1.0 mg/L, you can place the probe in a 0 mg/L solution for 30 to 90 seconds until readings stabilize, then press Calibrate (0 mg/L). You can also clear the currently-saved calibration by pressing Clear Calibration. Status messages will be sent to the Daemon Log, accessible from Config -> AoT Logs -> Daemon Log.
Calibrate (Air)	Button
Calibrate (0 mg/L)	Button
Clear Calibration	Button
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x66	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas EC~

Manufacturer: Atlas Scientific
Measurements: Electrical Conductivity
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Compensation: Measurement	Select Measurement (Input, Function)	Select a measurement for temperature compensation
Temperature Compensation: Max Age (Seconds)	Integer - Default Value: 120	The maximum age of the measurement to use
Commands
Calibration: a one- or two-point calibration can be performed. It's a good idea to clear the calibration before calibrating. Always perform a dry calibration with the probe in the air (not in any fluid). Then perform either a one- or two-point calibration with calibrated solutions. If performing a one-point calibration, use the Single Point Calibration field and button. If performing a two-point calibration, use the Low and High Point Calibration fields and buttons. Allow a minute or two after submerging your probe in a calibration solution for the measurements to equilibrate before calibrating to that solution. The EZO EC circuit default temperature compensation is set to 25 °C. If the temperature of the calibration solution is +/- 2 °C from 25 °C, consider setting the temperature compensation first. Note that at no point should you change the temperature compensation value during calibration. Therefore, if you have previously enabled temperature compensation, allow at least one measurement to occur (to set the compensation value), then disable the temperature compensation measurement while you calibrate. Status messages will be sent to the Daemon Log, accessible from Config -> AoT Logs -> Daemon Log.
Clear Calibration	Button
Calibrate Dry	Button
Single Point EC (µS)	Integer - Default Value: 84	The EC (µS) of the single point calibration solution
Calibrate Single Point	Button
Low Point EC (µS)	Integer - Default Value: 12880	The EC (µS) of the low point calibration solution
Calibrate Low Point	Button
High Point EC (µS)	Integer - Default Value: 80000	The EC (µS) of the high point calibration solution
Calibrate High Point	Button
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x64	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas Flow Meter~

Manufacturer: Atlas Scientific
Measurements: Total Volume, Flow Rate
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Set the Measurement Time Base to a value most appropriate for your anticipated flow (it will affect accuracy). This flow rate time base that is set and returned from the sensor will be converted to liters per minute, which is the default unit for this input module. If you desire a different rate to be stored in the database (such as liters per second or hour), then use the Convert to Unit option.

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Flow Meter Type	Select(Options: [Atlas Scientific 3/8" Flow Meter \| Atlas Scientific 1/4" Flow Meter \| Atlas Scientific 1/2" Flow Meter \| Atlas Scientific 3/4" Flow Meter \| Non-Atlas Scientific Flow Meter] (Default in bold)	Set the type of flow meter used
Atlas Meter Time Base	Select(Options: [Liters per Second \| Liters per Minute \| Liters per Hour] (Default in bold)	If using an Atlas Scientific flow meter, set the flow rate/time base
Internal Resistor	Select(Options: [Use Atlas Scientific Flow Meter \| Disable Internal Resistor \| 1 K Ω Pull-Up \| 1 K Ω Pull-Down \| 10 K Ω Pull-Up \| 10 K Ω Pull-Down \| 100 K Ω Pull-Up \| 100 K Ω Pull-Down] (Default in bold)	Set an internal resistor for the flow meter
Custom K Value(s)	Text	If using a non-Atlas Scientific flow meter, enter the meter's K value(s). For a single K value, enter '[volume per pulse],[number of pulses]'. For multiple K values (up to 16), enter '[volume at frequency],[frequency in Hz];[volume at frequency],[frequency in Hz];...'. Leave blank to disable.
K Value Time Base	Select(Options: [Use Atlas Scientific Flow Meter \| Liters per Second \| Liters per Minute \| Liters per Hour] (Default in bold)	If using a non-Atlas Scientific flow meter, set the flow rate/time base for the custom K values entered.
Commands
The total volume can be cleared with the following button or with the Clear Total Volume Function Action.
Clear Total: Volume	Button
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x68	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas Humidity~

Manufacturer: Atlas Scientific
Measurements: Humidity/Temperature
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
LED Mode	Select(Options: [Always On \| Always Off \| Only On During Measure] (Default in bold)	When to turn the LED on
Commands
New I2C Address	Text - Default Value: 0x6f	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas O2 (Oxygen Gas)~

Manufacturer: Atlas Scientific
Measurements: O2
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Compensation: Measurement	Select Measurement (Input, Function)	Select a measurement for temperature compensation
Temperature Compensation: Max Age (Seconds)	Integer - Default Value: 120	The maximum age of the measurement to use
Temperature Compensation: Manual	Decimal - Default Value: 20.0	If not using a measurement, set the temperature to compensate
LED Mode	Select(Options: [Always On \| Always Off \| Only On During Measure] (Default in bold)	When to turn the LED on
Commands
A one- or two-point calibration can be performed. After exposing the probe to a specific concentration of O2 until readings stabilize, press Calibrate (High). You can place the probe in a 0% O2 environment until readings stabilize, then press Calibrate (Zero). You can also clear the currently-saved calibration by pressing Clear Calibration, returning to the factory-set calibration. Status messages will be sent to the Daemon Log, accessible from Config -> AoT Logs -> Daemon Log.
High Point O2	Decimal - Default Value: 20.95	The high O2 calibration point (percent)
Calibrate (High)	Button
Calibrate (Zero)	Button
Clear Calibration	Button
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x69	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas ORP~

Manufacturer: Atlas Scientific
Measurements: Oxidation Reduction Potential
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Compensation: Measurement	Select Measurement (Input, Function)	Select a measurement for temperature compensation
Temperature Compensation: Max Age (Seconds)	Integer - Default Value: 120	The maximum age of the measurement to use
Commands
A one-point calibration can be performed. Enter the solution's mV, set the probe in the solution, then press Calibrate. You can also clear the currently-saved calibration by pressing Clear Calibration. Status messages will be sent to the Daemon Log, accessible from Config -> AoT Logs -> Daemon Log.
Calibration Solution mV	Integer - Default Value: 225	The value of the calibration solution, in mV
Calibrate	Button
Clear Calibration	Button
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x62	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas PT-1000~

Manufacturer: Atlas Scientific
Measurements: Temperature
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Commands
New I2C Address	Text - Default Value: 0x66	The new I2C to set the device to
Set I2C Address	Button
Temperature (°C)	Decimal - Default Value: 100.0	Temperature for single point calibration
Calibrate	Button
Clear Calibration	Button

Atlas Scientific: Atlas Pressure~

Manufacturer: Atlas Scientific
Measurements: Pressure
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
LED Mode	Select(Options: [Always On \| Always Off \| Only On During Measure] (Default in bold)	When to turn the LED on
Commands
New I2C Address	Text - Default Value: 0x6a	The new I2C to set the device to
Set I2C Address	Button

Atlas Scientific: Atlas pH~

Manufacturer: Atlas Scientific
Measurements: Ion Concentration
Interfaces: I²C, UART, FTDI
Libraries: pylibftdi/fcntl/io/serial
Dependencies: pylibftdi
Manufacturer URL: Link
Datasheet URL: Link

Calibration Measurement is an optional setting that provides a temperature measurement (in Celsius) of the water that the pH is being measured from.

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
FTDI Device	Text	The FTDI device connected to the input/output/etc.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Compensation: Measurement	Select Measurement (Input, Function)	Select a measurement for temperature compensation
Temperature Compensation: Max Age (Seconds)	Integer - Default Value: 120	The maximum age of the measurement to use
Commands
Calibration: a one-, two- or three-point calibration can be performed. It's a good idea to clear the calibration before calibrating. The first calibration must be the Mid point. The second must be the Low point. And the third must be the High point. You can perform a one-, two- or three-point calibration, but they must be performed in this order. Allow a minute or two after submerging your probe in a calibration solution for the measurements to equilibrate before calibrating to that solution. The EZO pH circuit default temperature compensation is set to 25 °C. If the temperature of the calibration solution is +/- 2 °C from 25 °C, consider setting the temperature compensation first. Note that if you have a Temperature Compensation Measurement selected from the Options, this will overwrite the manual Temperature Compensation set here, so be sure to disable this option if you would like to specify the temperature to compensate with. Status messages will be sent to the Daemon Log, accessible from Config -> AoT Logs -> Daemon Log.
Compensation Temperature (°C)	Decimal - Default Value: 25.0	The temperature of the calibration solutions
Set Temperature Compensation	Button
Clear Calibration	Button
Mid Point pH	Decimal - Default Value: 7.0	The pH of the mid point calibration solution
Calibrate Mid	Button
Low Point pH	Decimal - Default Value: 4.0	The pH of the low point calibration solution
Calibrate Low	Button
High Point pH	Decimal - Default Value: 10.0	The pH of the high point calibration solution
Calibrate High	Button
Calibration Export/Import: Export calibration to a series of strings. These can later be imported to restore the calibration. Watch the Daemon Log for the output.
Export Calibration	Button
Calibration String	Text	The calibration string to import
Import Calibration	Button
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x63	The new I2C to set the device to
Set I2C Address	Button

BOSCH: BME280 (Adafruit_BME280)~

Manufacturer: BOSCH
Measurements: Pressure/Humidity/Temperature
Interfaces: I²C
Libraries: Adafruit_BME280
Dependencies: Adafruit-GPIO, Adafruit_BME280
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

BOSCH: BME280 (Adafruit_CircuitPython_BME280)~

Manufacturer: BOSCH
Measurements: Pressure/Humidity/Temperature
Interfaces: I²C
Libraries: Adafruit_CircuitPython_BME280
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-bme280
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

BOSCH: BME280 (RPi.bme280)~

Manufacturer: BOSCH
Measurements: Pressure/Humidity/Temperature
Interfaces: I²C
Libraries: RPi.bme280
Dependencies: RPi.bme280
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

BOSCH: BME680 (Adafruit_CircuitPython_BME680)~

Manufacturer: BOSCH
Measurements: Temperature/Humidity/Pressure/Gas
Interfaces: I²C
Libraries: Adafruit_CircuitPython_BME680
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-bme680
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Humidity Oversampling	Select(Options: [NONE \| 1X \| 2X \| 4X \| 8X \| 16X] (Default in bold)	A higher oversampling value means more stable readings with less noise and jitter. However each step of oversampling adds ~2 ms latency, causing a slower response time to fast transients.
Temperature Oversampling	Select(Options: [NONE \| 1X \| 2X \| 4X \| 8X \| 16X] (Default in bold)	A higher oversampling value means more stable readings with less noise and jitter. However each step of oversampling adds ~2 ms latency, causing a slower response time to fast transients.
Pressure Oversampling	Select(Options: [NONE \| 1X \| 2X \| 4X \| 8X \| 16X] (Default in bold)	A higher oversampling value means more stable readings with less noise and jitter. However each step of oversampling adds ~2 ms latency, causing a slower response time to fast transients.
IIR Filter Size	Select(Options: [0 \| 1 \| 3 \| 7 \| 15 \| 31 \| 63 \| 127] (Default in bold)	Optionally remove short term fluctuations from the temperature and pressure readings, increasing their resolution but reducing their bandwidth.
Temperature Offset	Decimal	The amount to offset the temperature, either negative or positive
Sea Level Pressure (ha)	Decimal - Default Value: 1013.25	The pressure at sea level for the sensor location

BOSCH: BME680 (bme680)~

Manufacturer: BOSCH
Measurements: Temperature/Humidity/Pressure/Gas
Interfaces: I²C
Libraries: bme680
Dependencies: bme680, smbus2
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Humidity Oversampling	Select(Options: [NONE \| 1X \| 2X \| 4X \| 8X \| 16X] (Default in bold)	A higher oversampling value means more stable readings with less noise and jitter. However each step of oversampling adds ~2 ms latency, causing a slower response time to fast transients.
Temperature Oversampling	Select(Options: [NONE \| 1X \| 2X \| 4X \| 8X \| 16X] (Default in bold)	A higher oversampling value means more stable readings with less noise and jitter. However each step of oversampling adds ~2 ms latency, causing a slower response time to fast transients.
Pressure Oversampling	Select(Options: [NONE \| 1X \| 2X \| 4X \| 8X \| 16X] (Default in bold)	A higher oversampling value means more stable readings with less noise and jitter. However each step of oversampling adds ~2 ms latency, causing a slower response time to fast transients.
IIR Filter Size	Select(Options: [0 \| 1 \| 3 \| 7 \| 15 \| 31 \| 63 \| 127] (Default in bold)	Optionally remove short term fluctuations from the temperature and pressure readings, increasing their resolution but reducing their bandwidth.
Gas Heater Temperature (°C)	Integer - Default Value: 320	What temperature to set
Gas Heater Duration (ms)	Integer - Default Value: 150	How long of a duration to heat. 20-30 ms are necessary for the heater to reach the intended target temperature.
Gas Heater Profile	Select	Select one of the 10 configured heating durations/set points
Temperature Offset	Decimal	The amount to offset the temperature, either negative or positive

BOSCH: BMP180~

Manufacturer: BOSCH
Measurements: Pressure/Temperature
Interfaces: I²C
Libraries: Adafruit_BMP
Dependencies: Adafruit-BMP, Adafruit-GPIO
Datasheet URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

BOSCH: BMP280 (Adafruit_GPIO)~

Manufacturer: BOSCH
Measurements: Pressure/Temperature
Interfaces: I²C
Libraries: Adafruit_GPIO
Dependencies: Adafruit-GPIO
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

BOSCH: BMP280 (bmp280-python)~

Manufacturer: BOSCH
Measurements: Pressure/Temperature
Interfaces: I²C
Libraries: bmp280-python
Dependencies: smbus2, bmp280
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

This is similar to the other BMP280 Input, except it uses a different library, whcih includes the ability to set forced mode.

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Enable Forced Mode	Boolean	Enable heater to evaporate condensation. Turn on heater x seconds every y measurements.

CARTO: GL: Carto Maps~

Manufacturer: CARTO
Measurements: Status
Libraries: gis_carto
Manufacturer URL: Link

Data analysis-focused maps from CARTO DB. Offers restrained color schemes with Positron (light), Dark Matter (dark), and Voyager styles, designed to make data points and sensor information stand out.

Option	Type	Description
Active Map Styles

CO2Meter: K30~

Manufacturer: CO2Meter
Measurements: CO2
Interfaces: I²C, UART
Libraries: serial (UART)
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Catnip Electronics: Chirp~

Manufacturer: Catnip Electronics
Measurements: Light/Moisture/Temperature
Interfaces: I²C
Libraries: smbus2
Dependencies: smbus2
Manufacturer URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Commands
The I2C address can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x20	The new I2C to set the device to
Set I2C Address	Button

ChirpStack: ChirpStack: MQTT (Payload JMESPath Expression)~

Manufacturer: ChirpStack
Measurements: Variable measurements
Libraries: paho-mqtt, jmespath
Dependencies: paho-mqtt, jmespath

Subscribes to the ChirpStack v4 MQTT broker topic (application/+/device/+/event/up) to receive events, and applies per-channel JMESPath expressions to each event JSON to store measurements. Examples (https://jmespath.org): object.battery_V, object.battery_pct, max_by(rxInfo,&rssi).rssi, max_by(rxInfo,&snr).snr, deviceInfo.devEui.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
MQTT Host	Text - Default Value: localhost	MQTT broker hostname or IP address (e.g. localhost)
MQTT Port	Text - Default Value: 1883	MQTT broker port (default 1883, 8883 recommended for TLS)
MQTT Username	Text	Optional: broker authentication username
MQTT Password	Text	Optional: broker authentication password
Enable TLS	Boolean	Whether to use a TLS (SSL) connection (default off)
CA Certificate Path	Text	Optional: path to the CA certificate when using TLS
Client ID	Text - Default Value: client_E94Skyyx	Unique client ID for connecting to the server
Keepalive (sec)	Text - Default Value: 60	MQTT keepalive in seconds (default 60 sec)
Subscribe Topics	Text - Default Value: application/+/device/+/event/up	Comma-separated subscription topics (e.g. application/+/device/+/event/up)
QoS	Text	MQTT QoS level (0, 1, 2)
Device EUIs (comma-separated)	Text	Optional: process only specific devices. Enter EUIs separated by commas
Channel Options
Name	Text	A name to distinguish this from others
JMESPath Expression	Text	Evaluated against the entire received event (JSON)

Chirpstack: ChirpStack: REST API (Payload JMESPath Expression)~

Manufacturer: Chirpstack
Measurements: Variable measurements
Libraries: chirpstack-rest-api, requests, jmespath

Periodically calls the ChirpStack v4 REST API to fetch device events, and applies per-channel JMESPath expressions to each event JSON to store measurements. Examples (https://jmespath.org): object.battery_V, object.battery_pct, max_by(rxInfo,&rssi).rssi, max_by(rxInfo,&snr).snr, deviceInfo.devEui.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Start Offset (Seconds)	Integer	The duration to wait before the first operation
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
API Base URL	Text - Default Value: http://localhost:8090	Base address of the ChirpStack REST API (e.g. http://localhost:8080) (the REST proxy is typically on port 8090)
API Token	Text	Bearer token for accessing the ChirpStack REST API (issued from the admin console)
Tenant ID	Text	Optional: use to query only devices belonging to a specific tenant
Application ID	Text	Optional: use to query only devices belonging to a specific application
Device EUIs (comma-separated)	Text	Optional: enter the device EUIs to query, separated by commas. If empty, all devices in the application are targeted
Page size / limit	Text - Default Value: 50	Number of events to fetch in a single REST API call (page size)
Event kind	Text - Default Value: up	Type of events to fetch (e.g. up, join, status)
Fallback URL template	Text - Default Value: /api/devices/{dev_eui}/events?limit={limit}&kind={kind}&after={after}	URL template used for REST requests when the official Python client is unavailable (appended after the API Base URL). {dev_eui}, {limit}, {kind}, {after} are substituted automatically
Channel Options
Name	Text	A name to distinguish this from others
JMESPath Expression	Text	Evaluated against the full event JSON

Cozir: Cozir CO2~

Manufacturer: Cozir
Measurements: CO2/Humidity/Temperature
Interfaces: UART
Libraries: pierre-haessig/pycozir
Dependencies: cozir
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Ecowitt: Ecowitt Cloud API Weather Data~

Manufacturer: Ecowitt

To use the Ecowitt Cloud API, enter the Application Key, API Key, and device MAC address.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Measurement Period (sec)	Decimal - Default Value: 60	Enter the measurement interval in seconds.
Application Key	Text	Enter the Application Key issued by the Ecowitt platform.
API Key	Text	Enter the API Key issued by the Ecowitt platform.
Device MAC	Text	Enter the MAC address of the Ecowitt device.
Call Back	Text - Default Value: all	Enter the type of data to request (e.g. all).

Ecowitt: Ecowitt MQTT (JSON payload)~

Manufacturer: Ecowitt
Measurements: Variable measurements
Interfaces: AoT
Libraries: paho-mqtt, jmespath
Dependencies: paho-mqtt, jmespath

Subscribes to channels automatically generated based on the selected Ecowitt device type, extracts values from the URL-encoded or JSON payload sent over the MQTT topic using each channel's JMESPATH expression, and stores them in the database. Per-channel measurement units and conversion settings can be specified via custom options.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Ecowitt Device	Select(Options: [Weather Station \| Temperature/Humidity Sensor \| Temperature Sensor \| Soil Moisture Sensor \| Leaf Sensor \| Distance Sensor \| Air Quality Sensor] (Default in bold)
Host	Text - Default Value: localhost	Host or IP address
Port	Integer - Default Value: 1883	Host port number
Topic	Text - Default Value: gw	The topic to subscribe to
Keep Alive	Integer - Default Value: 60	Maximum amount of time between received signals. Set to 0 to disable.
Client ID	Text - Default Value: client_pPFiqPBB	Unique client ID for connecting to the server
Use Login	Boolean	Send login credentials
Use TLS	Boolean	Send login credentials using TLS
Username	Text - Default Value: user	Username for connecting to the server
Password	Text	Password for connecting to the server. Leave blank to disable.
Use Websockets	Boolean	Use websockets to connect to the server.
Channel Options
Name	Text	A name to distinguish this from others
JMESPATH Expression	Text	JMESPATH expression to find value in JSON response

Ecowitt: Ecowitt soil_sensor~

Manufacturer: Ecowitt

To use the Ecowitt Cloud API, enter the Application Key, API Key, and device MAC address.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Measurement Period (sec)	Decimal - Default Value: 60	Enter the measurement interval in seconds.
Application Key	Text	Enter the Application Key issued by the Ecowitt platform.
API Key	Text	Enter the API Key issued by the Ecowitt platform.
Device MAC	Text	Enter the MAC address of the Ecowitt device.
Channel Selection	Text - Default Value: 1	Select the channel to measure.

Ecowitt: Ecowitt temp and humidity sensor~

Manufacturer: Ecowitt

To use the Ecowitt Cloud API, enter the Application Key, API Key, and device MAC address.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Measurement Period (sec)	Decimal - Default Value: 60	Enter the measurement interval in seconds.
Application Key	Text	Enter the Application Key issued by the Ecowitt platform.
API Key	Text	Enter the API Key issued by the Ecowitt platform.
Device MAC	Text	Enter the MAC address of the Ecowitt device.
Channel Selection	Text - Default Value: 1	Select the channel to measure.

Esri: GL: Esri World Imagery~

Manufacturer: Esri
Measurements: Status
Libraries: gis_esri
Manufacturer URL: Link

Authoritative map service from global GIS leader Esri. Provides crisp and detailed World Imagery aerial satellite photos, optimized for accurate terrain and facility visualization.

GSI: JP: GSI Maps~

Manufacturer: GSI
Measurements: Status
Libraries: gis_gsi
Manufacturer URL: Link

High-precision public map service from Japan Geospatial Information Authority (GSI). Contains detailed terrain and place name information across Japan, with professional layers including standard maps, pale maps, and aerial photography.

Option	Type	Description
Map Style

Generic: Hall Flow Meter~

Manufacturer: Generic
Measurements: Flow Rate, Total Volume
Interfaces: GPIO
Libraries: pigpio
Dependencies: pigpio, pigpio

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Pulses per Liter	Decimal - Default Value: 1.0	Enter the conversion factor for this meter (pulses to Liter).
Commands
Clear Total: Volume	Button

Google: GL: Google Maps~

Manufacturer: Google
Measurements: Status
Libraries: gis_google
Manufacturer URL: Link

Most widely used Google web map service. Supports Road, Satellite, Hybrid, and Terrain modes based on vast geographic information. Terrain mode excels at showing contours and hillshading. Also supports Geocoding API for address-to-coordinate conversion. API key available from Google Developer Console.

Option	Type	Description
Google Maps API Key	Text
Map Style

ISRIC: GL: SoilGrids (Global Soil Info)~

Manufacturer: ISRIC
Measurements: Status
Libraries: gis_isric
Manufacturer URL: Link

Global soil characteristic map from World Soil Information Service (ISRIC). Visualizes soil composition (clay, sand, etc.), pH levels, and carbon content for geological analysis as overlayer data.

Option	Type	Description
Soil Property

Infineon: DPS310~

Manufacturer: Infineon
Measurements: Pressure/Temperature
Interfaces: I²C
Libraries: Adafruit_CircuitPython_DPS310
Dependencies: Adafruit-extended-bus, adafruit-circuitpython-dps310
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2, Link 3

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

KMA: KMA High-Resolution 500m~

Manufacturer: KMA
Additional URL: Link

After issuing a free API key from the KMA API Hub, data is requested based on the location (latitude/longitude) in the input settings. Note: the Korea Meteorological Administration API allows 20000 calls per day, and each call returns data for a single observation station.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
API Key	Text	Enter the API Key issued by the KMA API Hub.
Measurement Period (sec)	Decimal - Default Value: 300	Enter the measurement interval in seconds.
Enable Quality Control (QC)	Boolean - Default Value: True	Ignore or correct obvious outliers (e.g. humidity 0%, pressure 0hPa, etc.).
QC Hold Time (sec)	Decimal - Default Value: 1800	Replace with the last valid value within this time window.
Manual Backfill Period (min)	Decimal - Default Value: 1440	On user request, load this much past data. Default 1440 min (1 day).
Run Backfill Now	Boolean	When enabled after saving, performs a single backfill immediately and then turns off automatically.
QC: 0°C Accept Range (±°C)	Decimal - Default Value: 3.0	Accept 0°C only when the previous valid value is within this range of 0°C. Default ±3°C.

KMA: KMA Short-term Forecast~

Manufacturer: KMA
Additional URL: Link

This module provides short-term agricultural forecast data. Based on the most recent announcement, it collects forecast data for the time offset selected by the user. The API call uses a service key from the Public Data Portal, and extracts temperature, min/max temperature, wind speed, wind direction, sky condition, humidity, precipitation, precipitation probability, precipitation type, and fresh snowfall from the JSON response. (Data is available from 10 minutes after the announcement time.)

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
API Key	Text	Enter the KMA API service key issued by the Public Data Portal.
nx Coordinate	Text	Enter the nx value (number).
ny Coordinate	Text	Enter the ny value (number).
Forecast Hours Ahead	Select(Options: [1 \| 2 \| 3 \| 4 \| 5 \| 6 \| 7 \| 8 \| 9 \| 10 \| 11 \| 12] (Default in bold)	Select how many hours ahead of forecast data to use.
API Timeout (sec)	Integer - Default Value: 60	Set the API response timeout (default 60 sec).
API Retry Count	Integer - Default Value: 3	Set how many times to retry the same announcement time on an HTTP error.
API Retry Interval (sec)	Decimal - Default Value: 3.0	Time to wait between retries (default 3 sec).

KMA: KMA Station Data~

Manufacturer: KMA
Measurements: Humidity/Temperature/Pressure/Wind Speed/Wind Direction
Additional URL: Link

Issue a free API key from the KMA API Hub and enter the STN of the nearest observation station. Note: the free API allows 20000 calls per day, and each call returns data for a single observation station.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
API Key	Text	The API Key for this service's API
stn	Text	The stn to acquire the weather data

Kakao: KO: Kakao Map~

Manufacturer: Kakao
Measurements: Status
Libraries: gis_kakao
Manufacturer URL: Link

Option	Type	Description
Map Type

Korea Meteorological Administration: KR: KMA Weather~

Manufacturer: Korea Meteorological Administration
Measurements: Status
Libraries: gis_kma
Manufacturer URL: Link

KMA API Hub (apihub.kma.go.kr) 500m high-resolution observation data — displays location-based multi-channel weather information as a map legend. Uses the same API key as the KMA_weather_500 input.

Option	Type	Description
API Key (apihub.kma.go.kr authKey)	Text
Active Channels

MAXIM: DS1822~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: 1-Wire
Libraries: w1thermsensor
Dependencies: w1thermsensor
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Commands
Set the resolution, precision, and response time for the sensor. This setting will be written to the EEPROM to allow persistence after power loss. The EEPROM has a limited amount of writes (>50k).
Resolution	Select	Select the resolution for the sensor
Set Resolution	Button

MAXIM: DS1825~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: 1-Wire
Libraries: w1thermsensor
Dependencies: w1thermsensor
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Commands
Set the resolution, precision, and response time for the sensor. This setting will be written to the EEPROM to allow persistence after power loss. The EEPROM has a limited amount of writes (>50k).
Resolution	Select	Select the resolution for the sensor
Set Resolution	Button

MAXIM: DS18B20 (ow-shell)~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: 1-Wire
Libraries: ow-shell
Dependencies: ow-shell, owfs
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2, Link 3
Additional URL: Link

Warning: Counterfeit DS18B20 sensors are common and can cause a host of issues. Review the Additional URL for more information about how to determine if your sensor is authentic.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

MAXIM: DS18B20 (w1thermsensor)~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: 1-Wire
Libraries: w1thermsensor
Dependencies: w1thermsensor
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2, Link 3
Additional URL: Link

Warning: Counterfeit DS18B20 sensors are common and can cause a host of issues. Review the Additional URL for more information about how to determine if your sensor is authentic.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Offset	Decimal	The temperature offset (degrees Celsius) to apply
Commands
Set the resolution, precision, and response time for the sensor. This setting will be written to the EEPROM to allow persistence after power loss. The EEPROM has a limited amount of writes (>50k).
Resolution	Select	Select the resolution for the sensor
Set Resolution	Button

MAXIM: DS18S20~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: 1-Wire
Libraries: w1thermsensor
Dependencies: w1thermsensor
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Commands
Set the resolution, precision, and response time for the sensor. This setting will be written to the EEPROM to allow persistence after power loss. The EEPROM has a limited amount of writes (>50k).
Resolution	Select	Select the resolution for the sensor
Set Resolution	Button

MAXIM: DS28EA00~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: 1-Wire
Libraries: w1thermsensor
Dependencies: w1thermsensor
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Commands
Set the resolution, precision, and response time for the sensor. This setting will be written to the EEPROM to allow persistence after power loss. The EEPROM has a limited amount of writes (>50k).
Resolution	Select	Select the resolution for the sensor
Set Resolution	Button

MAXIM: MAX31850K~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: 1-Wire
Libraries: w1thermsensor
Dependencies: w1thermsensor
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Commands
Set the resolution, precision, and response time for the sensor. This setting will be written to the EEPROM to allow persistence after power loss. The EEPROM has a limited amount of writes (>50k).
Resolution	Select	Select the resolution for the sensor
Set Resolution	Button

MAXIM: MAX31855 (Gravity PT100) (smbus2)~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: I²C
Libraries: smbus2
Dependencies: smbus2
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

MAXIM: MAX31855 (Gravity PT100) (wiringpi)~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: I²C
Libraries: wiringpi
Dependencies: wiringpi
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

MAXIM: MAX31855 (Adafruit_MAX31855)~

Manufacturer: MAXIM
Measurements: Temperature (Object/Die)
Interfaces: UART
Libraries: Adafruit_MAX31855
Dependencies: Adafruit_MAX31855, Adafruit-GPIO
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Pin: Cable Select	Integer	GPIO (using BCM numbering): Pin: Cable Select
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

MAXIM: MAX31855 (adafruit-circuitpython-max31855)~

Manufacturer: MAXIM
Measurements: Temperature (Object/Die)
Interfaces: SPI
Libraries: adafruit-circuitpython-max31855
Dependencies: adafruit-circuitpython-max31855
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Chip Select Pin	Integer - Default Value: 5	Enter the GPIO Chip Select Pin for your device.

MAXIM: MAX31856~

Manufacturer: MAXIM
Measurements: Temperature (Object/Die)
Interfaces: UART
Libraries: RPi.GPIO
Dependencies: RPi.GPIO
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Pin: Cable Select	Integer	GPIO (using BCM numbering): Pin: Cable Select
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

MAXIM: MAX31865 (Adafruit-CircuitPython-MAX31865)~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: SPI
Libraries: Adafruit-CircuitPython-MAX31865
Dependencies: adafruit-circuitpython-max31865
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

This module was added to allow support for multiple sensors to be connected at the same time, which the original MAX31865 module was not designed for.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Chip Select Pin	Integer - Default Value: 8	Enter the GPIO Chip Select Pin for your device.
Number of wires	Select(Options: [2 Wires \| 3 Wires \| 4 Wires] (Default in bold)	Select the number of wires your thermocouple has.

MAXIM: MAX31865 (RPi.GPIO)~

Manufacturer: MAXIM
Measurements: Temperature
Interfaces: UART
Libraries: RPi.GPIO
Dependencies: RPi.GPIO
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Note: This module does not allow for multiple sensors to be connected at the same time. For multi-sensor support, use the MAX31865 CircuitPython Input.

Option	Type	Description
Pin: Cable Select	Integer	GPIO (using BCM numbering): Pin: Cable Select
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Manufacturer: MQTT
Measurements: Variable measurements
Interfaces: AoT
Libraries: paho-mqtt, jmespath
Dependencies: paho-mqtt, jmespath

A single topic is subscribed to and the returned JSON payload contains one or more key/value pairs. The given JSON Key is used as a JMESPATH expression to find the corresponding value that will be stored for that channel. Be sure you select and save the Measurement Unit for each channel. Once the unit has been saved, you can convert to other units in the Convert Measurement section. Example expressions for jmespath (https://jmespath.org) include temperature, sensors[0].temperature, and bathroom.temperature which refer to the temperature as a direct key within the first entry of sensors or as a subkey of bathroom, respectively. Jmespath elements and keys that contain special characters have to be enclosed in double quotes, e.g. "sensor-1".temperature. Warning: If using multiple MQTT Inputs or Functions, ensure the Client IDs are unique.

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Host	Text - Default Value: localhost	Host or IP address
Port	Integer - Default Value: 1883	Host port number
Topic	Text - Default Value: mqtt/test/input	The topic to subscribe to
Keep Alive	Integer - Default Value: 60	Maximum amount of time between received signals. Set to 0 to disable.
Client ID	Text - Default Value: client_jpEZlggi	Unique client ID for connecting to the server
Use Login	Boolean	Send login credentials
Use TLS	Boolean	Send login credentials using TLS
TLS CA Certificate	Text	Path to the CA certificate file that signed the broker certificate. Leave blank to use the system CA store (for brokers with a publicly-trusted certificate, e.g. Let's Encrypt).
Username	Text - Default Value: user	Username for connecting to the server
Password	Text	Password for connecting to the server. Leave blank to disable.
Use Websockets	Boolean	Use websockets to connect to the server.
Channel Options
Name	Text	A name to distinguish this from others
JMESPATH Expression	Text	JMESPATH expression to find value in JSON response

Manufacturer: MQTT
Measurements: Variable measurements
Interfaces: AoT
Libraries: paho-mqtt
Dependencies: paho-mqtt

A topic is subscribed to for each channel Subscription Topic and the returned payload value will be stored for that channel. Be sure you select and save the Measurement Unit for each of the channels. Once the unit has been saved, you can convert to other units in the Convert Measurement section. Warning: If using multiple MQTT Inputs or Functions, ensure the Client IDs are unique.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Host	Text - Default Value: localhost	Host or IP address
Port	Integer - Default Value: 1883	Host port number
Keep Alive	Integer - Default Value: 60	Maximum amount of time between received signals. Set to 0 to disable.
Client ID	Text - Default Value: client_6yUrtu3q	Unique client ID for connecting to the server
Use Login	Boolean	Send login credentials
Use TLS	Boolean	Send login credentials using TLS
TLS CA Certificate	Text	Path to the CA certificate file that signed the broker certificate. Leave blank to use the system CA store (for brokers with a publicly-trusted certificate, e.g. Let's Encrypt).
Username	Text - Default Value: user	Username for connecting to the server
Password	Text	Password for connecting to the server. Leave blank to disable.
Use Websockets	Boolean	Use websockets to connect to the server.
Channel Options
Name	Text	A name to distinguish this from others
Subscription Topic	Text	The MQTT topic to subscribe to

MapTiler: GL: MapTiler Vector~

Manufacturer: MapTiler
Measurements: Status
Libraries: gis_maptiler_vector
Manufacturer URL: Link

High-performance vector tile map service. Supports multiple styles (streets, light, dark, satellite, etc.) with excellent rendering performance and HD display.

Option	Type	Description
MapTiler API Key	Text
Map Style
Label Language	Text

Mapbox: GL: Mapbox~

Manufacturer: Mapbox
Measurements: Status
Libraries: gis_mapbox
Manufacturer URL: Link

Stylish Mapbox vector and tile maps with excellent customization. Supports Streets, Satellite, Dark, and Light styles with superior rendering performance for smooth map interaction.

Option	Type	Description
Mapbox Access Token	Text
Map Style

Melexis: MLX90393~

Manufacturer: Melexis
Measurements: Magnetic Flux
Interfaces: I²C
Libraries: Adafruit_CircuitPython_MLX90393
Dependencies: Adafruit-extended-bus, adafruit-circuitpython-mlx90393
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2, Link 3

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Melexis: MLX90614~

Manufacturer: Melexis
Measurements: Temperature (Ambient/Object)
Interfaces: I²C
Libraries: smbus2
Dependencies: smbus2
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Microchip: MCP3008 (Adafruit_CircuitPython_MCP3xxx)~

Manufacturer: Microchip
Measurements: Voltage (Analog-to-Digital Converter)
Interfaces: UART
Libraries: Adafruit_CircuitPython_MCP3xxx
Dependencies: adafruit-circuitpython-mcp3xxx
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Pin: Cable Select	Integer	GPIO (using BCM numbering): Pin: Cable Select
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
VREF (volts)	Decimal - Default Value: 3.3	Set the VREF voltage

Microchip: MCP3008 (Adafruit_MCP3008)~

Manufacturer: Microchip
Measurements: Voltage (Analog-to-Digital Converter)
Interfaces: UART
Libraries: Adafruit_MCP3008
Dependencies: Adafruit-MCP3008
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
Pin: Cable Select	Integer	GPIO (using BCM numbering): Pin: Cable Select
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
VREF (volts)	Decimal - Default Value: 3.3	Set the VREF voltage

Microchip: MCP3208~

Manufacturer: Microchip
Measurements: Voltage (Analog-to-Digital Converter)
Interfaces: SPI
Libraries: MCP3208
Dependencies: Adafruit-GPIO
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
Pin: Cable Select	Integer	GPIO (using BCM numbering): Pin: Cable Select
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
SPI Bus	Integer	The SPI bus ID.
SPI Device	Integer	The SPI device ID.
VREF (volts)	Decimal - Default Value: 3.3	Set the VREF voltage

Microchip: MCP342x (x=2,3,4,6,7,8)~

Manufacturer: Microchip
Measurements: Voltage (Analog-to-Digital Converter)
Interfaces: I²C
Libraries: MCP342x
Dependencies: smbus2, MCP342x
Manufacturer URLs: Link 1, Link 2, Link 3, Link 4, Link 5
Datasheet URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Microchip: MCP9808~

Manufacturer: Microchip
Measurements: Temperature
Interfaces: I²C
Libraries: Adafruit_MCP9808
Dependencies: Adafruit-GPIO, Adafruit_MCP9808
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Microsoft: GL: Bing Maps~

Manufacturer: Microsoft
Measurements: Status
Libraries: gis_bing
Manufacturer URL: Link

Microsoft global map service providing high-resolution aerial imagery (Aerial) and aerial with labels (Hybrid), with clean and precise road maps.

Option	Type	Description
Bing Maps API Key	Text
Map Style

Modbus: Modbus TCP (PLC)~

Manufacturer: Modbus
Measurements: Variable measurements
Interfaces: IP
Libraries: pymodbus
Dependencies: pymodbus

Reads coils and registers from a Modbus TCP device (PLC, gateway, meter). Define one channel per register to read. Several Inputs and Outputs pointing at the same host and port share a single connection automatically. Note that Modbus has no authentication or encryption — keep the device on an isolated network and never expose it to the internet.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Start Offset (Seconds)	Integer	The duration to wait before the first operation
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Host	Text	IP address or hostname of the Modbus TCP device
Port	Integer - Default Value: 502	TCP port of the Modbus TCP device (standard: 502)
Unit ID	Integer - Default Value: 1	Modbus unit/slave ID of the device. Usually 1 for a device addressed directly, or the slave address behind a serial gateway
Timeout (seconds)	Decimal - Default Value: 1.0	How long to wait for a response. One request takes at most timeout x (retries + 1)
Retries	Integer - Default Value: 1	Retries per request before it is treated as failed. Keep this low: a high value multiplies how long an unreachable device blocks a command
Channel Options
Name	Text	A name to distinguish this from others
Register Type	Select(Options: [Coil (read/write bit) \| Discrete Input (read-only bit) \| Holding Register (read/write word) \| Input Register (read-only word)] (Default in bold)	Which Modbus table this channel reads from
Register Address	Integer	Zero-based address within the selected table. Vendor documentation often lists one-based addresses (e.g. 40001 for holding register 0), so verify against the register map
Data Type	Select(Options: [Bit (coil / discrete input) \| int16 \| uint16 \| int32 (2 registers) \| uint32 (2 registers) \| float32 (2 registers)] (Default in bold)	How to interpret the value. Bit types apply to coils and discrete inputs; the rest apply to registers
Word Order	Select(Options: [Big endian (high word first) \| Little endian (low word first)] (Default in bold)	Register order for 32-bit types. Vendors differ, so if a value reads as nonsense while the register address is correct, try the other order
Scale Factor	Decimal - Default Value: 1.0	The raw value is multiplied by this. Use it when a device reports e.g. tenths of a degree (0.1)

Multiple Manufacturers: HC-SR04~

Manufacturer: Multiple Manufacturers
Measurements: Ultrasonic Distance
Interfaces: GPIO
Libraries: Adafruit_CircuitPython_HCSR04
Dependencies: libgpiod-dev, pyusb, adafruit-circuitpython-hcsr04
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link
Additional URL: Link

Option	Type	Description
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Trigger Pin	Integer	Enter the GPIO Trigger Pin for your device (BCM numbering).
Echo Pin	Integer	Enter the GPIO Echo Pin for your device (BCM numbering).

NASA: GL: Soil Moisture (NASA SMAP)~

Manufacturer: NASA
Measurements: Status
Libraries: gis_esa
Manufacturer URL: Link

Global surface soil moisture (0-5cm) from NASA's SMAP (Soil Moisture Active Passive) L4 product, delivered as a near-real-time overlay via NASA GIBS. Available at roughly 9km resolution with selectable dates, useful for irrigation planning and drought monitoring.

Option	Type	Description
Date Mode	Select
Custom Date	Text

NASA: NASA GIBS~

Manufacturer: NASA
Measurements: Status
Interfaces: AoT
Libraries: gis_nasa_gibs
Manufacturer URL: Link

Real-time Earth observation maps from NASA GIBS satellite system. Includes satellite imagery (Blue Marble) plus environmental data like temperature, clouds, and fires, selectable by date for time-series analysis.

Option	Type	Description
Satellite Layer
Date Mode	Select
Custom Date	Text

Naver: KO: Naver Map~

Manufacturer: Naver
Measurements: Status
Libraries: gis_naver
Manufacturer URL: Link

Option	Type	Description
Map Type

Open-Meteo: Open-Meteo (Coords, Hourly incl. Solar)~

Manufacturer: Open-Meteo
Measurements: Temperature/Humidity/Solar/Wind/Rain/VPD
Interfaces: AoT
Additional URL: Link

No API key needed — enter Latitude/Longitude only. Unlike most free weather sources this one reports solar radiation (W/m²), which the environment coordinator uses to lock out misting in strong sun. Note this is a forecast model value, not a measurement at your site. Free use is non-commercial (CC-BY 4.0); a paid key switches to the commercial endpoint.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
API Key (optional)	Text	Leave empty for free non-commercial use. A key from open-meteo.com switches to the commercial endpoint.

OpenStreetMap: GL: OpenStreetMap~

Manufacturer: OpenStreetMap
Measurements: Status
Libraries: gis_osm
Manufacturer URL: Link

Free map data created collaboratively by users worldwide in Wikipedia-style. Available at no cost with road and building information continuously updated by an active community. Standard web map with global coverage.

OpenTopoMap: GL: OpenTopoMap~

Manufacturer: OpenTopoMap
Measurements: Status
Libraries: gis_opentopomap
Manufacturer URL: Link

Terrain map service based on OpenStreetMap data with emphasized contours and hillshading. Clear differentiation for mountain terrain and slope analysis, high readability, suitable for hiking and outdoor activity visualization.

OpenWeather: OpenWeatherMap (City/Coords, Current)~

Manufacturer: OpenWeather
Measurements: Humidity/Temperature/Pressure/Wind
Additional URL: Link

Obtain a free API key at openweathermap.org. Enter a City OR Latitude/Longitude coordinates. Note: the free API subscription is limited to 60 calls per minute

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
API Key	Text	The API Key for this service's API
City	Text	City Name (Optional if using Coords)

OpenWeather: OpenWeatherMap (Lat/Lon, Current/Future)~

Manufacturer: OpenWeather
Measurements: Humidity/Temperature/Pressure/Wind
Interfaces: AoT
Additional URL: Link

Obtain a free API key at openweathermap.org. Notes: The free API subscription is limited to 60 calls per minute. If a Day (Future) time is selected, Minimum and Maximum temperatures are available as measurements.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
API Key	Text	The API Key for this service's API
Time	Select(Options: [Current (Present) \| 1 Day (Future) \| 2 Day (Future) \| 3 Day (Future) \| 4 Day (Future) \| 5 Day (Future) \| 6 Day (Future) \| 7 Day (Future) \| 1 Hour (Future) \| 2 Hours (Future) \| 3 Hours (Future) \| 4 Hours (Future) \| 5 Hours (Future) \| 6 Hours (Future) \| 7 Hours (Future) \| 8 Hours (Future) \| 9 Hours (Future) \| 10 Hours (Future) \| 11 Hours (Future) \| 12 Hours (Future) \| 13 Hours (Future) \| 14 Hours (Future) \| 15 Hours (Future) \| 16 Hours (Future) \| 17 Hours (Future) \| 18 Hours (Future) \| 19 Hours (Future) \| 20 Hours (Future) \| 21 Hours (Future) \| 22 Hours (Future) \| 23 Hours (Future) \| 24 Hours (Future) \| 25 Hours (Future) \| 26 Hours (Future) \| 27 Hours (Future) \| 28 Hours (Future) \| 29 Hours (Future) \| 30 Hours (Future) \| 31 Hours (Future) \| 32 Hours (Future) \| 33 Hours (Future) \| 34 Hours (Future) \| 35 Hours (Future) \| 36 Hours (Future) \| 37 Hours (Future) \| 38 Hours (Future) \| 39 Hours (Future) \| 40 Hours (Future) \| 41 Hours (Future) \| 42 Hours (Future) \| 43 Hours (Future) \| 44 Hours (Future) \| 45 Hours (Future) \| 46 Hours (Future) \| 47 Hours (Future) \| 48 Hours (Future)] (Default in bold)	Select the time for the current or forecast weather

OpenWeatherMap: GL: OpenWeatherMap~

Manufacturer: OpenWeatherMap
Measurements: Status
Libraries: gis_openweather
Manufacturer URL: Link

Weather-focused service displaying global weather information as map overlays. Provides real-time clouds, precipitation, temperature, wind speed, pressure, and radar data for intuitive weather situational awareness.

Option	Type	Description
API Key	Text
Active Layers

Panasonic: AMG8833~

Manufacturer: Panasonic
Measurements: 8x8 Temperature Grid
Interfaces: I²C
Libraries: Adafruit_AMG88xx/Pillow/colour
Dependencies: libjpeg-dev, zlib1g-dev, colour, Pillow, Adafruit_AMG88xx

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Power Monitor: RPi 6-Channel Power Monitor (v0.1.0)~

Manufacturer: Power Monitor
Measurements: AC Voltage, Power, Current, Power Factor
Libraries: rpi-power-monitor
Dependencies: rpi_power_monitor
Manufacturer URL: Link
Product URL: Link

See https://github.com/David00/rpi-power-monitor/wiki/Calibrating-for-Accuracy for calibration procedures.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Grid Voltage	Decimal - Default Value: 124.2	The AC voltage measured at the outlet
Transformer Voltage	Decimal - Default Value: 10.2	The AC voltage measured at the barrel plug of the 9 VAC transformer
CT1 Phase Correction	Decimal - Default Value: 1.0	The phase correction value for CT1
CT2 Phase Correction	Decimal - Default Value: 1.0	The phase correction value for CT2
CT3 Phase Correction	Decimal - Default Value: 1.0	The phase correction value for CT3
CT4 Phase Correction	Decimal - Default Value: 1.0	The phase correction value for CT4
CT5 Phase Correction	Decimal - Default Value: 1.0	The phase correction value for CT5
CT6 Phase Correction	Decimal - Default Value: 1.0	The phase correction value for CT6
CT1 Accuracy Calibration	Decimal - Default Value: 1.0	The accuracy calibration value for CT1
CT2 Accuracy Calibration	Decimal - Default Value: 1.0	The accuracy calibration value for CT2
CT3 Accuracy Calibration	Decimal - Default Value: 1.0	The accuracy calibration value for CT3
CT4 Accuracy Calibration	Decimal - Default Value: 1.0	The accuracy calibration value for CT4
CT5 Accuracy Calibration	Decimal - Default Value: 1.0	The accuracy calibration value for CT5
CT6 Accuracy Calibration	Decimal - Default Value: 1.0	The accuracy calibration value for CT6
AC Accuracy Calibration	Decimal - Default Value: 1.0	The accuracy calibration value for AC

Power Monitor: RPi 6-Channel Power Monitor (v0.4.0)~

Manufacturer: Power Monitor
Measurements: AC Voltage, Power, Energy, Current, Power Factor
Libraries: rpi-power-monitor
Dependencies: rpi_power_monitor
Manufacturer URL: Link
Product URL: Link

See https://david00.github.io/rpi-power-monitor/docs/v0.3.0/calibration.html for calibration documentation.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Period (Seconds) for kWh Measuring	Integer - Default Value: 5	How often to acquire measurements to calculate kWh
Grid Voltage	Decimal - Default Value: 124.2	The AC voltage measured at the outlet
Transformer Voltage	Decimal - Default Value: 10.2	The AC voltage measured at the barrel plug of the 9 VAC transformer
AC Frequency (Hz)	Integer - Default Value: 60	The frequency of the AC voltage
CT1 Calibration	Decimal - Default Value: 1.0	The calibration value for CT1
CT1 Rating	Decimal - Default Value: 100	The Amp rating for the CT1 clamp
CT2 Calibration	Decimal - Default Value: 1.0	The calibration value for CT2
CT2 Rating	Decimal - Default Value: 100	The Amp rating for the CT2 clamp
CT3 Calibration	Decimal - Default Value: 1.0	The calibration value for CT3
CT3 Rating	Decimal - Default Value: 100	The Amp rating for the CT3 clamp
CT4 Calibration	Decimal - Default Value: 1.0	The calibration value for CT4
CT4 Rating	Decimal - Default Value: 100	The Amp rating for the CT4 clamp
CT5 Calibration	Decimal - Default Value: 1.0	The calibration value for CT5
CT5 Rating	Decimal - Default Value: 100	The Amp rating for the CT5 clamp
CT6 Calibration	Decimal - Default Value: 1.0	The calibration value for CT6
CT6 Rating	Decimal - Default Value: 100	The Amp rating for the CT6 clamp
AC Calibration	Decimal - Default Value: 1.0	The calibration value for AC
Commands
Clear the running kWh totals.
Channel to Clear	Select(Options: [All Channels \| Channel 1 \| Channel 2 \| Channel 3 \| Channel 4 \| Channel 5 \| Channel 6] (Default in bold)	The channel(s) to clear the kWh total and start back at 0.
Clear kWh Total	Button

RAKwireless: RAK3172 Valve Controller: Heartbeat (ChirpStack MQTT)~

Manufacturer: RAKwireless
Measurements: Battery, LoRa Class, HB Period, Valve States, RSSI, SNR
Libraries: paho-mqtt
Dependencies: paho-mqtt

Directly decodes the RAK3172 valve controller's heartbeat (FPort 225) payload from the ChirpStack v4 MQTT broker and stores battery voltage, node class, HB period, valve states, and RSSI/SNR. This input is used as the measurement source for lorawan_mode_manager's input_node_class / input_node_hb / input_vbat / input_rssi / input_snr.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
MQTT Host	Text - Default Value: localhost	ChirpStack MQTT broker hostname or IP address
MQTT Port	Integer - Default Value: 1883	MQTT port (default 1883)
MQTT Username	Text	Broker authentication username (leave empty if none)
MQTT Password	Text	Broker authentication password
Enable TLS	Boolean	Whether to use a TLS (SSL) connection
CA Certificate Path	Text	Path to the CA certificate file when using TLS
Client ID	Text - Default Value: aot_rak3172hb_tnQuQt	Unique MQTT client ID
Application ID (MQTT Topic)	Text - Default Value: +	Enter an ID to subscribe to a specific app only. Leave empty to use "+" (all).
Device EUI Filter	Text	Process only specific devices. Leave empty to receive all (multiple can be specified, comma-separated).
Decode Base HB Frame	Boolean - Default Value: True	Decode the 0xA5 base frame (battery + class) on FPort 225.
Decode Ext HB Frame	Boolean - Default Value: True	Decode the 0xA6 ext frame (HB period, actual class, valve states, etc.) on FPort 225.

ROHM: BH1750~

Manufacturer: ROHM
Measurements: Light
Interfaces: I²C
Libraries: smbus2
Dependencies: smbus2
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

RainViewer: GL: RainViewer (Radar)~

Manufacturer: RainViewer
Measurements: Status
Libraries: gis_rainviewer
Manufacturer URL: Link

RainViewer radar precipitation data overlay. Supports real-time rainfall tracking and animation. Compatible with both vector and raster modes.

Option	Type	Description
API Key	Text
Color Scheme	Select
Smoothing	Boolean

Raspberry Pi Foundation: Sense HAT~

Manufacturer: Raspberry Pi Foundation
Measurements: hum/temp/press/compass/magnet/accel/gyro
Interfaces: I²C
Libraries: sense-hat
Dependencies: git, Bash Commands (see Module for details), sense-hat
Manufacturer URL: Link

This module acquires measurements from the Raspberry Pi Sense HAT sensors, which include the LPS25H, LSM9DS1, and HTS221.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Remote Sensing: Satellite Analysis~

Manufacturer: Remote Sensing
Measurements: Analysis Channels
Interfaces: AoT
Libraries: requests

Collects environmental data from satellite analysis and GIS layers based on the device location. Supports auto-adjustment for data gaps (e.g. coastal areas).

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Active GIS Source	Select	Select the satellite/GIS analysis source.
Auto-adjust Location	Boolean - Default Value: True	Automatically search nearby valid coordinates if data is missing at the exact location (Spiral Search).

Ruuvi: RuuviTag~

Manufacturer: Ruuvi
Measurements: Acceleration/Humidity/Pressure/Temperature
Interfaces: BT
Libraries: ruuvitag_sensor
Dependencies: psutil, bluez, bluez-hcidump, ruuvitag-sensor
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
Bluetooth MAC (XX:XX:XX:XX:XX:XX)	Text	The Hci location of the Bluetooth device.
Bluetooth Adapter (hci[X])	Text	The adapter of the Bluetooth device.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

STMicroelectronics: VL53L0X~

Manufacturer: STMicroelectronics
Measurements: Millimeter (Time-of-Flight Distance)
Interfaces: I²C
Libraries: VL53L0X_rasp_python
Dependencies: VL53L0X
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Accuracy	Select(Options: [Good Accuracy (33 ms, 1.2 m range) \| Better Accuracy (66 ms, 1.2 m range) \| Best Accuracy (200 ms, 1.2 m range) \| Long Range (33 ms, 2 m) \| High Speed, Low Accuracy (20 ms, 1.2 m)] (Default in bold)	Set the accuracy. A longer measurement duration yields a more accurate measurement
Commands
New I2C Address	Text - Default Value: 0x52	The new I2C to set the device to
Set I2C Address	Button

STMicroelectronics: VL53L1X~

Manufacturer: STMicroelectronics
Measurements: Millimeter (Time-of-Flight Distance)
Interfaces: I²C
Libraries: VL53L1X
Dependencies: smbus2, vl53l1x
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Notes when setting a custom timing budget: A higher timing budget results in greater measurement accuracy, but also a higher power consumption. The inter measurement period must be >= the timing budget, otherwise it will be double the expected value.

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Range	Select(Options: [Short Range \| Medium Range \| Long Range \| Custom Timing Budget] (Default in bold)	Select a range or select to set a custom Timing Budget and Inter Measurement Period.
Timing Budget (microseconds)	Integer - Default Value: 66000	Set the timing budget. Must be less than or equal to the Inter Measurement Period.
Inter Measurement Period (milliseconds)	Integer - Default Value: 70	Set the Inter Measurement Period

STMicroelectronics: VL53L4CD~

Manufacturer: STMicroelectronics
Measurements: Millimeter (Time-of-Flight Distance)
Interfaces: I²C
Libraries: Adafruit-CircuitPython-VL53l4CD
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-vl53l4cd
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Timing Budget (ms)	Integer - Default Value: 50	Set the timing budget between 10 to 200 ms. A longer duration yields a more accurate measurement.
Inter-Measurement Period (ms)	Integer	Valid range between Timing Budget and 5000 ms (0 to disable)
Commands
The I2C address of the sensor can be changed. Enter a new address in the 0xYY format (e.g. 0x22, 0x50), then press Set I2C Address. Remember to deactivate the Input and change the I2C address option after setting the new address.
New I2C Address	Text - Default Value: 0x29	The new I2C to set the device to
Set I2C Address	Button

Seeed: SenseCAP OpenAPI Sensor~

Manufacturer: Seeed

Polls the SenseCAP OpenAPI directly for a SenseCAP LoRaWAN sensor node, bypassing the LoRaWAN network server. Requires an API ID/Access API Key created in the SenseCAP portal, and the device Node EUI. Select the Device Type matching the physical sensor so only its relevant channels are created.

Option	Type	Description
Measurement Period (sec)	Decimal - Default Value: 300	Enter the measurement interval in seconds.
Device Type	Select(Options: [Air Temperature and Humidity Sensor \| Light Intensity Sensor \| CO2 Sensor \| Barometric Pressure Sensor \| Soil Moisture and Temperature Sensor \| Wind Direction Sensor \| Wind Speed Sensor \| Rain Gauge \| Compact Weather Station 5-in-1 (S500) \| Compact Weather Station 3-in-1 (S300) \| Compact Weather Station 4-in-1 (S400) \| Soil Temperature and VWC Sensor \| Multilayer Soil Moisture and Temperature Sensor \| Soil Moisture, Temperature and EC Sensor \| LoRaWAN 8-in-1 Compact Weather Station (S2120) \| Compact Weather Station 10-in-1 (S1000) \| pH Sensor (S2106) \| Air Temperature, Humidity and Dew Point Sensor \| Temperature Sensor] (Default in bold)	Select the type of SenseCAP sensor this node is, so the correct measurement channels are used.
Node EUI	Text	Enter the SenseCAP device Node EUI.
API ID	Text	Enter the API ID issued by the SenseCAP portal (Organization/Security Credentials).
Access API Key	Text	Enter the Access API Key issued by the SenseCAP portal.
Commands
Fetch Historical Data	Button

Seeedstudio: DHT11/22~

Manufacturer: Seeedstudio
Measurements: Humidity/Temperature
Interfaces: GROVE
Libraries: grovepi
Dependencies: grovepi
Manufacturer URLs: Link 1, Link 2

Enter the Grove Pi+ GPIO pin connected to the sensor and select the sensor type.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Sensor Type	Select(Options: [DHT11 (Blue) \| DHT22 (White)] (Default in bold)	Sensor type

Senseair: K96~

Manufacturer: Senseair
Measurements: Methane/Moisture/CO2/Pressure/Humidity/Temperature
Interfaces: UART
Libraries: Serial

Option	Type	Description
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Sensirion: SCD-4x (40, 41)~

Manufacturer: Sensirion
Measurements: CO2/Temperature/Humidity
Interfaces: I²C
Libraries: Adafruit_CircuitPython_SCD4x
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-scd4x
Manufacturer URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Offset	Decimal - Default Value: 4.0	Set the sensor temperature offset
Altitude (m)	Integer	Set the sensor altitude (meters)
Automatic Self-Calibration	Boolean	Set the sensor automatic self-calibration
Persist Settings	Boolean - Default Value: True	Settings will persist after powering off
Commands
You can force the CO2 calibration for a specific CO2 concentration value (in ppmv). The sensor needs to be active for at least 3 minutes prior to calibration.
CO2 Concentration (ppmv)	Decimal - Default Value: 400.0	Calibrate to this CO2 concentration that the sensor is being exposed to (in ppmv)
Calibrate CO2	Button

Sensirion: SCD30 (Adafruit_CircuitPython_SCD30)~

Manufacturer: Sensirion
Measurements: CO2/Humidity/Temperature
Interfaces: I²C
Libraries: Adafruit_CircuitPython_SCD30
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitPython-scd30
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
I2C Frequency: The SCD-30 has temperamental I2C with clock stretching. The datasheet recommends starting at 50,000 Hz.
I2C Frequency (Hz)	Integer - Default Value: 50000
Automatic Self Ccalibration (ASC): To work correctly, the sensor must be on and active for 7 days after enabling ASC, and exposed to fresh air for at least 1 hour per day. Consult the manufacturer’s documentation for more information.
Enable Automatic Self Calibration	Boolean
Temperature Offset: Specifies the offset to be added to the reported measurements to account for a bias in the measured signal. Must be a positive value, and will reduce the recorded temperature by that amount. Give the sensor adequate time to acclimate after setting this value. Value is in degrees Celsius with a resolution of 0.01 degrees and a maximum value of 655.35 C.
Temperature Offset	Decimal
Ambient Air Pressure (mBar): Specify the ambient air pressure at the measurement location in mBar. Setting this value adjusts the CO2 measurement calculations to account for the air pressure’s effect on readings. Values must be in mBar, from 700 to 1200 mBar.
Ambient Air Pressure (mBar)	Integer - Default Value: 1200
Altitude: Specifies the altitude at the measurement location in meters above sea level. Setting this value adjusts the CO2 measurement calculations to account for the air pressure’s effect on readings.
Altitude (m)	Integer - Default Value: 100
Commands
A soft reset restores factory default values.
Soft Reset	Button
Forced Re-Calibration: The SCD-30 is placed in an environment with a known CO2 concentration, this concentration value is entered in the CO2 Concentration (ppmv) field, then the Foce Calibration button is pressed. But how do you come up with that known value? That is a caveat of this approach and Sensirion suggests three approaches: 1. Using a separate secondary calibrated CO2 sensor to provide the value. 2. Exposing the SCD-30 to a controlled environment with a known value. 3. Exposing the SCD-30 to fresh outside air and using a value of 400 ppm.
CO2 Concentration (ppmv)	Integer - Default Value: 800	The CO2 concentration of the sensor environment when forcing calibration
Force Recalibration	Button

Sensirion: SCD30 (scd30_i2c)~

Manufacturer: Sensirion
Measurements: CO2/Humidity/Temperature
Interfaces: I²C
Libraries: scd30_i2c
Dependencies: scd30-i2c
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Automatic Self Ccalibration (ASC): To work correctly, the sensor must be on and active for 7 days after enabling ASC, and exposed to fresh air for at least 1 hour per day. Consult the manufacturer’s documentation for more information.
Enable Automatic Self Calibration	Boolean
Commands
A soft reset restores factory default values.
Soft Reset	Button

Sensirion: SHT1x/7x~

Manufacturer: Sensirion
Measurements: Humidity/Temperature
Interfaces: GPIO
Libraries: sht_sensor
Dependencies: sht-sensor
Manufacturer URLs: Link 1, Link 2

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Sensirion: SHT2x (sht20)~

Manufacturer: Sensirion
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: sht20
Dependencies: sht20
Manufacturer URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Resolution	Select(Options: [11-bit \| 12-bit \| 13-bit \| 14-bit] (Default in bold)	The resolution of the temperature measurement

Sensirion: SHT2x (smbus2)~

Manufacturer: Sensirion
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: smbus2
Dependencies: smbus2
Manufacturer URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Sensirion: SHT31-D~

Manufacturer: Sensirion
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: Adafruit_CircuitPython_SHT31
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-sht31d
Manufacturer URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Offset	Decimal	The temperature offset (degrees Celsius) to apply

Sensirion: SHT3x (30, 31, 35)~

Manufacturer: Sensirion
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: Adafruit_SHT31
Dependencies: Adafruit-GPIO, Adafruit-SHT31
Manufacturer URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Enable Heater	Boolean	Enable heater to evaporate condensation. Turn on heater x seconds every y measurements
Heater On Seconds (Seconds)	Decimal - Default Value: 1.0	How long to turn the heater on
Heater On Period	Integer - Default Value: 10	After how many measurements to turn the heater on. This will repeat

Sensirion: SHT4X~

Manufacturer: Sensirion
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: Adafruit_CircuitPython_SHT4X
Dependencies: pyusb, Adafruit-extended-bus, adafruit_circuitpython_sht4x
Manufacturer URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Sensirion: SHTC3~

Manufacturer: Sensirion
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: Adafruit_CircuitPython_SHT3C
Dependencies: pyusb, Adafruit-extended-bus, adafruit_circuitpython_shtc3
Manufacturer URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Sensorion: SHT31 Smart Gadget~

Manufacturer: Sensorion
Measurements: Humidity/Temperature
Interfaces: BT
Libraries: bluepy
Dependencies: pi-bluetooth, libglib2.0-dev, bluepy
Manufacturer URL: Link

Option	Type	Description
Bluetooth MAC (XX:XX:XX:XX:XX:XX)	Text	The Hci location of the Bluetooth device.
Bluetooth Adapter (hci[X])	Text	The adapter of the Bluetooth device.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Download Stored Data	Boolean - Default Value: True	Download the data logged to the device.
Set Logging Interval (Seconds)	Integer - Default Value: 600	Set the logging interval the device will store measurements on its internal memory.

Silicon Labs: SI1145~

Manufacturer: Silicon Labs
Measurements: Light (UV/Visible/IR), Proximity (cm)
Interfaces: I²C
Libraries: si1145
Dependencies: SI1145
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Silicon Labs: Si7021~

Manufacturer: Silicon Labs
Measurements: Temperature/Humidity
Interfaces: I²C
Libraries: Adafruit_CircuitPython_SI7021
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-si7021
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Sonoff: TH16/10 (Tasmota firmware) with AM2301/Si7021~

Manufacturer: Sonoff
Measurements: Humidity/Temperature
Libraries: requests
Dependencies: requests
Manufacturer URL: Link

This Input module allows the use of any temperature/humidity sensor with the TH10/TH16. Changing the Sensor Name option changes the key that's queried from the returned dictionary of measurements. If you would like to use this module with a version of this device that uses the AM2301, change Sensor Name to AM2301.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
IP Address	Text - Default Value: 192.168.0.100	The IP address of the device
Sensor Name	Text - Default Value: SI7021	The name of the sensor connected to the device (specific key name in the returned dictionary)

Sonoff: TH16/10 (Tasmota firmware) with AM2301~

Manufacturer: Sonoff
Measurements: Humidity/Temperature
Libraries: requests
Dependencies: requests
Manufacturer URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
IP Address	Text - Default Value: 192.168.0.100	The IP address of the device

Sonoff: TH16/10 (Tasmota firmware) with DS18B20~

Manufacturer: Sonoff
Measurements: Temperature
Libraries: requests
Dependencies: requests
Manufacturer URL: Link

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
IP Address	Text - Default Value: 192.168.0.100	The IP address of the device

Stadia Maps: GL: Stadia Maps~

Manufacturer: Stadia Maps
Measurements: Status
Libraries: gis_stadia
Manufacturer URL: Link

High-quality design-focused map server from Stadia Maps. Provides clean layouts with eye-comfortable colors and high-quality fonts using Alidade Smooth, Dark, OSMBright styles, ideal for professional dashboard creation.

Option	Type	Description
Stadia/Stamen API Key	Text
Map Style

Statistics Korea: KO: SGIS (Statistics Korea)~

Manufacturer: Statistics Korea
Measurements: Status
Libraries: gis_sgis
Manufacturer URL: Link

Statistical geographic information service from Statistics Korea (SGIS). Optimal domestic service for spatial analysis and visualization of statistical data including population, households, and businesses by administrative district.

Option	Type	Description
SGIS Service ID (Consumer Key)	Text
SGIS Security Key (Consumer Secret)	Text
Data Configuration
Statistic Subject	Select
Year (YYYY)	Text
Target Admin Code (adm_cd)	Text
Visualization	Select

TE Connectivity: HTU21D (Adafruit_CircuitPython_HTU21D)~

Manufacturer: TE Connectivity
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: Adafruit_CircuitPython_HTU21D
Dependencies: Adafruit-extended-bus, adafruit-circuitpython-HTU21D
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Temperature Offset	Decimal	The temperature offset (degrees Celsius) to apply

TE Connectivity: HTU21D (pigpio)~

Manufacturer: TE Connectivity
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: pigpio
Dependencies: pigpio, pigpio
Manufacturer URL: Link
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

TP-Link: Kasa WiFi Power Plug/Strip Energy Statistics~

Manufacturer: TP-Link
Measurements: kilowatt hours
Interfaces: IP
Libraries: python-kasa
Dependencies: python-kasa, aio_msgpack_rpc
Manufacturer URL: Link

This measures from several Kasa power devices (plugs/strips) capable of measuring energy consumption. These include, but are not limited to the KP115 and HS600.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Device Type	Select	The type of Kasa device
Host	Text - Default Value: 0.0.0.0	Host or IP address
Asyncio RPC Port	Integer - Default Value: 18369	The port to start the asyncio RPC server. Must be unique from other Kasa Outputs.
Commands
The total kWh can be cleared with the following button or with the Clear Total kWh Function Action. This will also clear all energy stats on the device, not just the total kWh.
Clear Total: Kilowatt-hour	Button

Tasmota: Tasmota Outlet Energy Monitor (HTTP)~

Manufacturer: Tasmota
Measurements: Total Energy, Amps, Watts
Interfaces: HTTP
Libraries: requests
Manufacturer URL: Link
Product URL: Link

This input queries the energy usage information from a WiFi outlet that is running the tasmota firmware. There are many WiFi outlets that support tasmota, and many of of those have energy monitoring capabilities. When used with an MQTT Output, you can both control your tasmota outlets as well as mionitor their energy usage.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Host	Text - Default Value: 192.168.0.50	Host or IP address

Texas Instruments: ADS1015~

Manufacturer: Texas Instruments
Measurements: Voltage (Analog-to-Digital Converter)
Interfaces: I²C
Libraries: Adafruit_CircuitPython_ADS1x15
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-ads1x15

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Measurements to Average	Integer - Default Value: 5	The number of times to measure each channel. An average of the measurements will be stored.

Texas Instruments: ADS1115: Generic Analog pH/EC~

Manufacturer: Texas Instruments
Measurements: Ion Concentration/Electrical Conductivity
Interfaces: I²C
Libraries: Adafruit_CircuitPython_ADS1x15
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-ads1x15

This input relies on an ADS1115 analog-to-digital converter (ADC) to measure pH and/or electrical conductivity (EC) from analog sensors. You can enable or disable either measurement if you want to only connect a pH sensor or an EC sensor by selecting which measurements you want to under Measurements Enabled. Select which channel each sensor is connected to on the ADC. There are default calibration values initially set for the Input. There are also functions to allow you to easily calibrate your sensors with calibration solutions. If you use the Calibrate Slot actions, these values will be calculated and will replace the currently-set values. You can use the Clear Calibration action to delete the database values and return to using the default values. If you delete the Input or create a new Input to use your ADC/sensors with, you will need to recalibrate in order to store new calibration data.

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
ADC Channel: pH	Select(Options: [Channel 0 \| Channel 1 \| Channel 2 \| Channel 3] (Default in bold)	The ADC channel the pH sensor is connected
ADC Channel: EC	Select(Options: [Channel 0 \| Channel 1 \| Channel 2 \| Channel 3] (Default in bold)	The ADC channel the EC sensor is connected
Temperature Compensation
Temperature Compensation: Measurement	Select Measurement (Input, Function)	Select a measurement for temperature compensation
Temperature Compensation: Max Age (Seconds)	Integer - Default Value: 120	The maximum age of the measurement to use
pH Calibration Data
Cal data: V1 (internal)	Decimal - Default Value: 1.5	Calibration data: Voltage
Cal data: pH1 (internal)	Decimal - Default Value: 7.0	Calibration data: pH
Cal data: T1 (internal)	Decimal - Default Value: 25.0	Calibration data: Temperature
Cal data: V2 (internal)	Decimal - Default Value: 2.032	Calibration data: Voltage
Cal data: pH2 (internal)	Decimal - Default Value: 4.0	Calibration data: pH
Cal data: T2 (internal)	Decimal - Default Value: 25.0	Calibration data: Temperature
EC Calibration Data
EC cal data: V1 (internal)	Decimal - Default Value: 0.232	EC calibration data: Voltage
EC cal data: EC1 (internal)	Decimal - Default Value: 1413.0	EC calibration data: EC
EC cal data: T1 (internal)	Decimal - Default Value: 25.0	EC calibration data: EC
EC cal data: V2 (internal)	Decimal - Default Value: 2.112	EC calibration data: Voltage
EC cal data: EC2 (internal)	Decimal - Default Value: 12880.0	EC calibration data: EC
EC cal data: T2 (internal)	Decimal - Default Value: 25.0	EC calibration data: EC
Commands
pH Calibration Actions: Place your probe in a solution of known pH. Set the known pH value in the "Calibration buffer pH" field, and press "Calibrate pH, slot 1". Repeat with a second buffer, and press "Calibrate pH, slot 2". You don't need to change the values under "Custom Options".
Calibration buffer pH	Decimal - Default Value: 7.0	This is the nominal pH of the calibration buffer, usually labelled on the bottle.
Calibrate pH, slot 1	Button
Calibrate pH, slot 2	Button
Clear pH Calibration Slots	Button
EC Calibration Actions: Place your probe in a solution of known EC. Set the known EC value in the "Calibration standard EC" field, and press "Calibrate EC, slot 1". Repeat with a second standard, and press "Calibrate EC, slot 2". You don't need to change the values under "Custom Options".
Calibration standard EC	Decimal - Default Value: 1413.0	This is the nominal EC of the calibration standard, usually labelled on the bottle.
Calibrate EC, slot 1	Button
Calibrate EC, slot 2	Button
Clear EC Calibration Slots	Button

Texas Instruments: ADS1115~

Manufacturer: Texas Instruments
Measurements: Voltage (Analog-to-Digital Converter)
Interfaces: I²C
Libraries: Adafruit_CircuitPython_ADS1x15
Dependencies: pyusb, Adafruit-extended-bus, adafruit-circuitpython-ads1x15

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Measurements to Average	Integer - Default Value: 5	The number of times to measure each channel. An average of the measurements will be stored.

Texas Instruments: ADS1256: Generic Analog pH/EC~

Manufacturer: Texas Instruments
Measurements: Ion Concentration/Electrical Conductivity
Interfaces: UART
Libraries: wiringpi, aot-inc/PiPyADC-py3
Dependencies: wiringpi, pipyadc_py3

This input relies on an ADS1256 analog-to-digital converter (ADC) to measure pH and/or electrical conductivity (EC) from analog sensors. You can enable or disable either measurement if you want to only connect a pH sensor or an EC sensor by selecting which measurements you want to under Measurements Enabled. Select which channel each sensor is connected to on the ADC. There are default calibration values initially set for the Input. There are also functions to allow you to easily calibrate your sensors with calibration solutions. If you use the Calibrate Slot actions, these values will be calculated and will replace the currently-set values. You can use the Clear Calibration action to delete the database values and return to using the default values. If you delete the Input or create a new Input to use your ADC/sensors with, you will need to recalibrate in order to store new calibration data.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
ADC Channel: pH	Select(Options: [Not Connected \| Channel 0 \| Channel 1 \| Channel 2 \| Channel 3 \| Channel 4 \| Channel 5 \| Channel 6 \| Channel 7] (Default in bold)	The ADC channel the pH sensor is connected
ADC Channel: EC	Select(Options: [Not Connected \| Channel 0 \| Channel 1 \| Channel 2 \| Channel 3 \| Channel 4 \| Channel 5 \| Channel 6 \| Channel 7] (Default in bold)	The ADC channel the EC sensor is connected
Temperature Compensation
Temperature Compensation: Measurement	Select Measurement (Input, Function)	Select a measurement for temperature compensation
Temperature Compensation: Max Age (Seconds)	Integer - Default Value: 120	The maximum age of the measurement to use
pH Calibration Data
Cal data: V1 (internal)	Decimal - Default Value: 1.5	Calibration data: Voltage
Cal data: pH1 (internal)	Decimal - Default Value: 7.0	Calibration data: pH
Cal data: T1 (internal)	Decimal - Default Value: 25.0	Calibration data: Temperature
Cal data: V2 (internal)	Decimal - Default Value: 2.032	Calibration data: Voltage
Cal data: pH2 (internal)	Decimal - Default Value: 4.0	Calibration data: pH
Cal data: T2 (internal)	Decimal - Default Value: 25.0	Calibration data: Temperature
EC Calibration Data
EC cal data: V1 (internal)	Decimal - Default Value: 0.232	EC calibration data: Voltage
EC cal data: EC1 (internal)	Decimal - Default Value: 1413.0	EC calibration data: EC
EC cal data: T1 (internal)	Decimal - Default Value: 25.0	EC calibration data: EC
EC cal data: V2 (internal)	Decimal - Default Value: 2.112	EC calibration data: Voltage
EC cal data: EC2 (internal)	Decimal - Default Value: 12880.0	EC calibration data: EC
EC cal data: T2 (internal)	Decimal - Default Value: 25.0	EC calibration data: EC
Calibration	Select	Set the calibration method to perform during Input activation
Commands
pH Calibration Actions: Place your probe in a solution of known pH. Set the known pH value in the `Calibration buffer pH` field, and press `Calibrate pH, slot 1`. Repeat with a second buffer, and press `Calibrate pH, slot 2`. You don't need to change the values under `Custom Options`.
Calibration buffer pH	Decimal - Default Value: 7.0	This is the nominal pH of the calibration buffer, usually labelled on the bottle.
Calibrate pH, slot 1	Button
Calibrate pH, slot 2	Button
Clear pH Calibration Slots	Button
EC Calibration Actions: Place your probe in a solution of known EC. Set the known EC value in the `Calibration standard EC` field, and press `Calibrate EC, slot 1`. Repeat with a second standard, and press `Calibrate EC, slot 2`. You don't need to change the values under `Custom Options`.
Calibration standard EC	Decimal - Default Value: 1413.0	This is the nominal EC of the calibration standard, usually labelled on the bottle.
Calibrate EC, slot 1	Button
Calibrate EC, slot 2	Button
Clear EC Calibration Slots	Button

Texas Instruments: ADS1256~

Manufacturer: Texas Instruments
Measurements: Voltage (Waveshare, Analog-to-Digital Converter)
Interfaces: UART
Libraries: wiringpi, aot-inc/PiPyADC-py3
Dependencies: wiringpi, pipyadc_py3

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Calibration	Select	Set the calibration method to perform during Input activation

Texas Instruments: ADS1x15~

Manufacturer: Texas Instruments
Measurements: Voltage (Analog-to-Digital Converter)
Interfaces: I²C
Libraries: Adafruit_ADS1x15 [DEPRECATED]
Dependencies: Adafruit-GPIO, Adafruit-ADS1x15

The Adafruit_ADS1x15 is deprecated. It's advised to use The Circuit Python ADS1x15 Input.

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Measurements to Average	Integer - Default Value: 5	The number of times to measure each channel. An average of the measurements will be stored.

Texas Instruments: HDC1000~

Manufacturer: Texas Instruments
Measurements: Humidity/Temperature
Interfaces: I²C
Libraries: fcntl/io
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Texas Instruments: INA219x~

Manufacturer: Texas Instruments
Measurements: Electrical Current (DC)
Interfaces: I²C
Libraries: Adafruit_CircuitPython
Dependencies: adafruit-circuitpython-ina219, Adafruit-extended-bus
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Measurements to Average	Integer - Default Value: 5	The number of times to measure each channel. An average of the measurements will be stored.
Calibration Range	Select(Options: [32V @ 2A max (default) \| 32V @ 1A max \| 16V @ 400mA max \| 16V @ 5A max] (Default in bold)	Set the device calibration range
Bus Voltage Range	Select(Options: [(0x00) - 16V \| (0x01) - 32V (default)] (Default in bold)	Set the bus voltage range
Bus ADC Resolution	Select(Options: [(0x00) - 9 Bit / 1 Sample \| (0x01) - 10 Bit / 1 Sample \| (0x02) - 11 Bit / 1 Sample \| (0x03) - 12 Bit / 1 Sample (default) \| (0x09) - 12 Bit / 2 Samples \| (0x0A) - 12 Bit / 4 Samples \| (0x0B) - 12 Bit / 8 Samples \| (0x0C) - 12 Bit / 16 Samples \| (0x0D) - 12 Bit / 32 Samples \| (0x0E) - 12 Bit / 64 Samples \| (0x0F) - 12 Bit / 128 Samples] (Default in bold)	Set the Bus ADC Resolution.
Shunt ADC Resolution	Select(Options: [(0x00) - 9 Bit / 1 Sample \| (0x01) - 10 Bit / 1 Sample \| (0x02) - 11 Bit / 1 Sample \| (0x03) - 12 Bit / 1 Sample (default) \| (0x09) - 12 Bit / 2 Samples \| (0x0A) - 12 Bit / 4 Samples \| (0x0B) - 12 Bit / 8 Samples \| (0x0C) - 12 Bit / 16 Samples \| (0x0D) - 12 Bit / 32 Samples \| (0x0E) - 12 Bit / 64 Samples \| (0x0F) - 12 Bit / 128 Samples] (Default in bold)	Set the Shunt ADC Resolution.

Texas Instruments: TMP006~

Manufacturer: Texas Instruments
Measurements: Temperature (Object/Die)
Interfaces: I²C
Libraries: Adafruit_TMP
Dependencies: Adafruit-TMP
Datasheet URL: Link
Product URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

The Things Network: The Things Network: Data Storage (TTN v2)~

Manufacturer: The Things Network
Measurements: Variable measurements
Libraries: requests
Dependencies: requests

This Input receives and stores measurements from the Data Storage Integration on The Things Network.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Start Offset (Seconds)	Integer	The duration to wait before the first operation
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Application ID	Text	The Things Network Application ID
App API Key	Text	The Things Network Application API Key
Device ID	Text	The Things Network Device ID
Channel Options
Name	Text	A name to distinguish this from others
Variable Name	Text	The TTN variable name

The Things Network: The Things Network: Data Storage (TTN v3, Payload Key)~

Manufacturer: The Things Network
Measurements: Variable measurements
Libraries: requests
Dependencies: requests

This Input receives and stores measurements from the Data Storage Integration on The Things Network. If you have key/value pairs as your payload, enter the key name in Variable Name and the corresponding value for that key will be stored in the measurement database.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Start Offset (Seconds)	Integer	The duration to wait before the first operation
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Application ID	Text	The Things Network Application ID
App API Key	Text	The Things Network Application API Key
Device ID	Text	The Things Network Device ID
Channel Options
Name	Text	A name to distinguish this from others
Variable Name	Text	The TTN variable name

The Things Network: The Things Network: Data Storage (TTN v3, Payload jmespath Expression)~

Manufacturer: The Things Network
Measurements: Variable measurements
Libraries: requests, jmespath
Dependencies: requests, jmespath

This Input receives and stores measurements from the Data Storage Integration on The Things Network. The given Payload jmespath Expression is used as a JMESPATH expression to find the corresponding value that will be stored for that channel. Be sure you select and save the Measurement Unit for each channel. Once the unit has been saved, you can convert to other units in the Convert Measurement section. Example expressions for jmespath (https://jmespath.org) include temperature, sensors[0].temperature, and bathroom.temperature which refer to the temperature as a direct key within the first entry of sensors or as a subkey of bathroom, respectively. Jmespath elements and keys that contain special characters have to be enclosed in double quotes, e.g. "sensor-1".temperature.

Option	Type	Description
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Start Offset (Seconds)	Integer	The duration to wait before the first operation
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Application ID	Text	The Things Network Application ID
App API Key	Text	The Things Network Application API Key
Device ID	Text	The Things Network Device ID
Channel Options
Name	Text	A name to distinguish this from others
Payload jmespath Expression	Text	The TTN jmespath expression to return the value to store

Thunderforest: GL: Thunderforest~

Manufacturer: Thunderforest
Measurements: Status
Libraries: gis_thunderforest
Manufacturer URL: Link

Unique themed maps tailored for specific purposes using OpenStreetMap data. Experience visually striking styles including cycling routes (Cycle), public transport (Transport), night maps, and rugged landscapes.

Option	Type	Description
Thunderforest API Key	Text
Map Style

Vworld: KO: Vworld~

Manufacturer: Vworld
Measurements: Status
Libraries: gis_vworld
Manufacturer URL: Link

Vworld spatial information open platform from Korea Ministry of Land, Infrastructure and Transport. Provides the most precise national high-resolution aerial photography, digital maps, cadastral maps, and real-time traffic data. The most specialized national standard map for domestic business support.

Option	Type	Description
API Key	Text
Registered Domain	Text
Map Layer / Style
Show Legend	Boolean

Winsen: MH-Z14A~

Manufacturer: Winsen
Measurements: CO2
Interfaces: UART
Libraries: serial
Dependencies: RPi.GPIO
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Automatic Self-calibration	Boolean - Default Value: True	Enable automatic self-calibration
Measurement Range	Select(Options: [400 - 2000 ppmv \| 400 - 5000 ppmv \| 400 - 10000 ppmv] (Default in bold)	Set the measuring range of the sensor
The CO2 measurement can also be obtained using PWM via a GPIO pin. Enter the pin number below or leave blank to disable this option. This also makes it possible to obtain measurements even if the UART interface is not available (note that the sensor can't be configured / calibrated without a working UART interface).
GPIO Override	Text	Obtain readings using PWM on this GPIO pin instead of via UART
Commands
Calibrate Zero Point	Button
Span Point (ppmv)	Integer - Default Value: 2000	The ppmv concentration for a span point calibration
Calibrate Span Point	Button

Winsen: MH-Z16~

Manufacturer: Winsen
Measurements: CO2
Interfaces: UART, I²C
Libraries: smbus2/serial
Dependencies: smbus2
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Winsen: MH-Z19~

Manufacturer: Winsen
Measurements: CO2
Interfaces: UART
Libraries: serial
Datasheet URL: Link

This is the version of the sensor that does not include the ability to conduct automatic baseline correction (ABC). See the B version of the sensor if you wish to use ABC.

Option	Type	Description
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Measurement Range	Select(Options: [0 - 1000 ppmv \| 0 - 2000 ppmv \| 0 - 3000 ppmv \| 0 - 5000 ppmv] (Default in bold)	Set the measuring range of the sensor
Commands
Calibrate Zero Point	Button
Span Point (ppmv)	Integer - Default Value: 2000	The ppmv concentration for a span point calibration
Calibrate Span Point	Button

Winsen: MH-Z19B~

Manufacturer: Winsen
Measurements: CO2
Interfaces: UART
Libraries: serial
Manufacturer URL: Link
Datasheet URL: Link

This is the B version of the sensor that includes the ability to conduct automatic baseline correction (ABC).

Option	Type	Description
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Automatic Baseline Correction	Boolean	Enable automatic baseline correction (ABC)
Measurement Range	Select(Options: [0 - 1000 ppmv \| 0 - 2000 ppmv \| 0 - 3000 ppmv \| 0 - 5000 ppmv \| 0 - 10000 ppmv] (Default in bold)	Set the measuring range of the sensor
Commands
Calibrate Zero Point	Button
Span Point (ppmv)	Integer - Default Value: 2000	The ppmv concentration for a span point calibration
Calibrate Span Point	Button

Winsen: ZH03B~

Manufacturer: Winsen
Measurements: Particulates
Interfaces: UART
Libraries: serial
Manufacturer URL: Link
Datasheet URL: Link

Option	Type	Description
UART Device	Text	The UART device location (e.g. /dev/ttyUSB1)
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Fan Off After Measure	Boolean	Turn the fan on only during the measurement
Fan On Duration (Seconds)	Decimal - Default Value: 50.0	How long to turn the fan on before acquiring measurements
Number of Measurements	Integer - Default Value: 3	How many measurements to acquire. If more than 1 are acquired that are less than 1001, the average of the measurements will be stored.

Xiaomi: Miflora~

Manufacturer: Xiaomi
Measurements: EC/Light/Moisture/Temperature
Interfaces: BT
Libraries: miflora
Dependencies: libglib2.0-dev, miflora, bluepy

Option	Type	Description
Bluetooth MAC (XX:XX:XX:XX:XX:XX)	Text	The Hci location of the Bluetooth device.
Bluetooth Adapter (hci[X])	Text	The adapter of the Bluetooth device.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete

Xiaomi: Mijia LYWSD03MMC (ATC and non-ATC modes)~

Manufacturer: Xiaomi
Measurements: Battery/Humidity/Temperature
Interfaces: BT
Libraries: bluepy/bluez
Dependencies: libglib2.0, bluez, bluetooth, libbluetooth-dev, bluepy, bluetooth

More information about ATC mode can be found at https://github.com/JsBergbau/MiTemperature2

Option	Type	Description
Bluetooth MAC (XX:XX:XX:XX:XX:XX)	Text	The Hci location of the Bluetooth device.
Bluetooth Adapter (hci[X])	Text	The adapter of the Bluetooth device.
Measurements Enabled	Multi-Select	The measurements to record
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete
Enable ATC Mode	Boolean	Enable sensor ATC mode

ams: AS7341~

Manufacturer: ams
Measurements: Light
Interfaces: I²C
Libraries: Adafruit-CircuitPython-AS7341
Dependencies: adafruit-extended-bus, adafruit-circuitpython-as7341
Manufacturer URL: Link
Datasheet URL: Link
Product URLs: Link 1, Link 2, Link 3

Option	Type	Description
I²C Address	Text	The address of the I²C device.
I²C Bus	Integer	The Bus the I²C device is connected.
Period (Seconds)	Decimal	The duration between measurements or actions
Pre Output	Select	Turn the selected output on before taking every measurement
Pre Out Duration (Seconds)	Decimal	If a Pre Output is selected, set the duration to turn the Pre Output on for before every measurement is acquired.
Pre During Measure	Boolean	Check to turn the output off after (opposed to before) the measurement is complete